Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

New to the forum
#1

Hello.
I live in Spain and I am new to the forum.
I have several radios Valve, but so far no Philco.
I wanted to have a radio that can restore and I've decided on a 80 jr.
When I receive it I will put pictures, but you need an extensive restoration.
A greeting.
José
#2

Welcome to the Phorum! We are looking forward to seeing your pictures.

Steve

M R Radios   C M Tubes
#3

Welcome. Always like to here from new members. Lot of good & knowledgeable people here to help you if needed.
#4

Hola Jose,
Welcome!

You are sure to be an expert at restoring radios in no time flat with these guys to guide you.

I just got my first 80jr this week so it will be nice to see another one get restored!

Kirk

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#5

Welcome to the Phorum!! There are several threads on this Phorum that are related to the 80Jr. If you are new to restoration here is another good place to start reading: http://antiqueradio.org/begin.htm
#6

Hello and Welcome! There are a lot of nice and helpful people on this forum to help you out with the workings of your radio. Hope to see pictures of your radio soon.
#7

Hola Jose,

Si decide que necesita ayuda, solo pregunta.
Suerte!
#8

Welcome, Jose!

I am looking forward to seeing your 80 jr.

It's not how bad you mess up, it's how well you can recover.
#9

I want to thank you for the great reception towards me.

When you receive the 80jr. I will provide photographs, sure I will need help and advice, I am now reading most forum threads to get familiar.

A greeting.
#10

The seller told me that the numbering is 326407.
What does that mean ?.

Somewhere law an article about it, but did not locate.
#11

Could be serial #, could be chassis #....no es muy importante.
What is important is that this is 80jr.
#12

Hola José,

Si necessitas de ayuda... ya sabes que puedes contar com ela.
Saludos
Carlos

Regards from Portugal,
Carlos
#13

Thank you very much Carlos.
Always so friendly.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM
Philco model 38 code 121 not receiving signal.
I think this thing is way more accurate than my Walmart DMM. :DStormlord5500 — 08:19 AM
Philco model 38 code 121 not receiving signal.
Thankyou for the kind words sir. I double checked it with my component tester and it read 2.7 ohms at .02mH.Stormlord5500 — 08:14 AM
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM

[-]
Who's Online
There are currently 830 online users. [Complete List]
» 2 Member(s) | 828 Guest(s)
AvatarAvatar

>