1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 46-1203, radio doesn't work.
rghines1
Member
***
Posts: 190
Threads: 8
Joined: Oct 2005
City: Lexington, SC
#18

04-01-2009, 10:02 AM
It attenuates any RF coupling that can occur between the heater filaments and cathodes. This is commonly used on FM and TV filaments strings where the frequencies are two magnitudes higher.

Richard
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco 46-1203, radio doesn't work. - by Guest - 02-04-2008, 09:47 PM
[No subject] - by TonyJSenior - 02-05-2008, 06:07 PM
[No subject] - by TonyJSenior - 02-05-2008, 07:48 PM
[No subject] - by Guest - 02-06-2008, 04:28 AM
[No subject] - by TonyJSenior - 02-06-2008, 08:26 AM
[No subject] - by Guest - 02-06-2008, 01:14 PM
[No subject] - by TonyJSenior - 02-06-2008, 01:23 PM
46-1203 volume control - by Guest - 06-19-2008, 11:44 AM
46-1203 volume control - by Guest - 06-19-2008, 11:59 AM
[No subject] - by gary rabbitt - 06-20-2008, 02:06 PM
Re: Philco 46-1203, radio doesn't work. - by Guest - 07-19-2008, 03:38 AM
Re: 46-1203 volume control - by Guest - 07-19-2008, 03:43 AM
philco 46-1203 - by Guest - 08-30-2008, 12:03 AM
[No subject] - by BDM - 08-30-2008, 01:13 AM
Re: Philco 46-1203, radio doesn't work. - by Guest - 09-04-2008, 12:14 AM
Re: Philco 46-1203, radio doesn't work. - by Guest - 09-04-2008, 02:09 AM
Re: Philco 46-1203, radio doesn't work. - by rghines1 - 04-01-2009, 10:02 AM



Users browsing this thread:
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently 942 online users. [Complete List]
» 2 Member(s) | 940 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration