Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

RCA C15-3 floor model
#4

This is a new find, was not aware of another on ARF. 1936 is no doubt the correct year and was a little puzzled when two radio books and nostalgiaair schematic said 1935. Must admit RCA is not among my favorites of radio brands. The lady advertised it as a 1940s radio for $100. Called just in case the owner was mistaken, not a big fan of 40s radios. When she emailed me the pictures I was floored and did not quibble over the price. This is my highest tube count radio and first to be factory fused. Thanks for your comments.

Richard


Messages In This Thread
RCA C15-3 floor model - by rghines1 - 04-12-2009, 06:05 PM
RE: RCA C15-3 floor model - by rghines1 - 03-14-2021, 09:38 AM
RE: RCA C15-3 floor model - by Ron Ramirez - 03-14-2021, 10:47 AM
RE: RCA C15-3 floor model - by mikethedruid - 03-14-2021, 10:56 AM
RE: RCA C15-3 floor model - by Ron Ramirez - 03-14-2021, 11:03 AM
RE: RCA C15-3 floor model - by morzh - 03-14-2021, 12:36 PM
RE: RCA C15-3 floor model - by rghines1 - 03-14-2021, 01:05 PM
RE: RCA C15-3 floor model - by rghines1 - 03-14-2021, 01:55 PM
RE: RCA C15-3 floor model - by Ron Ramirez - 03-14-2021, 02:34 PM
RE: RCA C15-3 floor model - by Brad Winder - 03-17-2021, 12:22 AM
RE: RCA C15-3 floor model - by Ron Ramirez - 03-17-2021, 08:58 AM
RE: RCA C15-3 floor model - by Arran - 03-17-2021, 07:42 PM
Re: RCA C15-3 floor model - by Doug Houston - 04-13-2009, 01:34 AM
Re: RCA C15-3 floor model - by Texasrocker - 04-13-2009, 03:53 AM
Re: RCA C15-3 floor model - by rghines1 - 04-13-2009, 10:02 AM
Re: RCA C15-3 floor model - by exray - 04-13-2009, 11:56 AM
Re: RCA C15-3 floor model - by Doug Houston - 04-13-2009, 03:13 PM
Re: RCA C15-3 floor model - by Arran - 04-24-2009, 10:02 PM
Re: RCA C15-3 floor model - by Arran - 04-24-2009, 10:36 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 656 online users. [Complete List]
» 1 Member(s) | 655 Guest(s)
Avatar

>