Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

my 37-61 project...
#22

I have continued to tweak the alignment of the 37-61, and it is now dead on on both bands, and is surprisingly sensitive and selective. Even with only about 6 feet of wire attached to the antenna terminal, no ground, on the workbench in my cellar I am able to pick up WWV on both 10 MC and 15 MC, faint but clear, which speaks well for the set since WWV is kind of hard to pick up here because of a big hill just to my west. The AM band is excellent too. On the same antenna I am able to pick up both WOR 710 in New York, and 740 Zoomer radio out of Toronto, Canada, both of which I kind of use as a benchmark. I am now satisfied that the radio is performing about as well as it can. Now I just have to wait until the weather warms up and I can continue work on the cabinet, the adventure of which I am chronicling in the cabinet section.


Messages In This Thread
my 37-61 project... - by mikethedruid - 09-26-2015, 05:12 PM
RE: my 37-61 project... - by mikethedruid - 09-30-2015, 04:29 PM
RE: my 37-61 project... - by mikethedruid - 10-02-2015, 06:44 PM
RE: my 37-61 project... - by mikethedruid - 10-05-2015, 07:40 PM
RE: my 37-61 project... - by mikethedruid - 10-17-2015, 01:03 PM
RE: my 37-61 project... - by KCMike - 10-17-2015, 01:56 PM
RE: my 37-61 project... - by mikethedruid - 10-17-2015, 02:53 PM
RE: my 37-61 project... - by mikethedruid - 11-16-2015, 08:23 PM
RE: my 37-61 project... - by mikethedruid - 11-17-2015, 12:51 AM
RE: my 37-61 project... - by klondike98 - 11-17-2015, 01:46 AM
RE: my 37-61 project... - by mikethedruid - 11-17-2015, 03:06 AM
RE: my 37-61 project... - by mikethedruid - 12-09-2015, 10:08 PM
RE: my 37-61 project... - by kiwi_steve - 12-10-2015, 01:07 AM
RE: my 37-61 project... - by mikethedruid - 12-11-2015, 09:38 AM
RE: my 37-61 project... - by mikethedruid - 12-13-2015, 12:10 AM
RE: my 37-61 project... - by mikethedruid - 12-14-2015, 08:38 PM
RE: my 37-61 project... - by mikethedruid - 12-27-2015, 08:22 PM
RE: my 37-61 project... - by mikethedruid - 12-27-2015, 11:38 PM
RE: my 37-61 project... - by mikethedruid - 12-28-2015, 01:53 AM
RE: my 37-61 project... - by klondike98 - 12-28-2015, 10:20 AM
RE: my 37-61 project... - by mikethedruid - 01-01-2016, 01:53 AM
RE: my 37-61 project... - by mikethedruid - 01-27-2016, 03:58 PM
RE: my 37-61 project... - by KCMike - 01-27-2016, 05:35 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently no members online.

>