Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Zenith 6C05Z production change 3 ???
#1

           I though if you BUY a schematic for a radio ,TV,,,,that you would get the Production Change Bulletin #3 with it,,(DIDN'T  KNOW THERE IS ONE) ( and still don't have it) this little set is becoming a pain in the butt,,, I got A  extra resistor in it and jumpers on 2 tubes ,,,for some reason ,,smarter than I can figure out,,,and don't have, the true reading (ohms) for this resistor,,it measures 139.6 ohms,,WHO KNOWS,---,it pertains to 35L6GT,,,on the Chassis, it has pin 6 ---87volts with resistor 139.6 ohms going to Pin 4--instead of the 87 volts going to Pin 4-----then 12SQ7GT,,they have a jump that goes from Pin 3 to Pin 5 and to Pin8,,, SOO,,this little set worked Very well,,, Changing out Paper capacitors ,resistors ,and 2 tubes ,,soo,,I am letting youall Know about this,, whom may come across this in the future,, Icon_crazy Icon_clap CHEERS


Messages In This Thread
Zenith 6C05Z production change 3 ??? - by Kenneth F. Besso Jr. - 02-18-2016, 09:45 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 647 online users. [Complete List]
» 1 Member(s) | 646 Guest(s)
Avatar

>