Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Pros and Cons of Refinishing the 511 Series cabinets
#19

Jim Berg Wrote:I am not sure what prices these set bring, but to have an artist duplicate the work on the set would not be cheap. I would be more inclined to clean it up and maybe have some touch up done. I would like to find one of these in good shape someday, but have not seen any over the years. A good artist should be able to touch up the cabinet and it should blend in very well. My mom was an artist and did some restorations on old paintings. It required mixing different colors to get the proper shade of the aged paint.

Actually it is probably easier to paint a replica then it is to touch up an original, as you mentioned you need to custom mix the paints just right so the repairs don't stand out against the old paint. If you were to take a 511, strip it, and repaint it to replicate a 512, 513, etc, then you would be starting with a blank "canvas" so to speak. There would be no need to exactly match colours or brush strokes since no two of the originals were the same to begin with. To me the flowers on most of those models remind me of the ones that tole painters make, several layers of replicated brush strokes to form leaves and flower pedals, making an acceptable facsimile should not be too difficult to someone artistically inclined.
With the 515 model, "The Impressionistic", was that a design that was offered from the factory? A prototype maybe? Or some type of one off that was special ordered?
Best Regards
Arran


Messages In This Thread
Re: Pros and Cons of Refinishing the 511 Series cabinets - by Arran - 05-07-2009, 09:51 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>