Hickok 600A Calibration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Hickok 600A Calibration

Steve McDonald
Junior Member

Posts: 35
Threads: 7
Joined: Apr 2016
City: Medford, Oregon

#13

04-13-2016, 02:38 PM

I don't use calibration tubes. I made a a 5mA. transformer I use as a current source. 5 mA. corresponds to 1000 mhos on your meter. The most important part of calibration is to make sure the tested tubes are tested at the proper voltage.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Hickok 600A Calibration - by etech - 01-12-2016, 06:13 PM

RE: Hickok 600A Calibration - by etech - 01-18-2016, 01:21 PM

RE: Hickok 600A Calibration - by Eliot Ness - 01-18-2016, 02:48 PM

RE: Hickok 600A Calibration - by etech - 01-18-2016, 06:46 PM

RE: Hickok 600A Calibration - by Eliot Ness - 01-18-2016, 08:20 PM

RE: Hickok 600A Calibration - by morzh - 01-18-2016, 09:02 PM

RE: Hickok 600A Calibration - by codefox1 - 01-19-2016, 01:36 PM

RE: Hickok 600A Calibration - by etech - 01-19-2016, 06:48 PM

RE: Hickok 600A Calibration - by TA Forbes - 02-15-2016, 04:35 PM

RE: Hickok 600A Calibration - by keith49vj3 - 03-26-2016, 09:50 AM

RE: Hickok 600A Calibration - by morzh - 03-26-2016, 12:45 PM

RE: Hickok 600A Calibration - by TV MAN - 03-29-2016, 09:51 AM

RE: Hickok 600A Calibration - by Steve McDonald - 04-13-2016, 02:38 PM

RE: Hickok 600A Calibration - by Phlogiston - 10-25-2016, 12:55 PM

RE: Hickok 600A Calibration - by Phlogiston - 10-25-2016, 12:51 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me