1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
My 'new' Philco 630 CSX chairside!
Nathan Slingerland
Super Moderator
******
Posts: 1,889
Threads: 214
Joined: May 2015
City: Seattle State, Province, Country: WA
#5

04-24-2016, 06:36 PM
(04-24-2016, 02:31 PM)palegreenthumb Wrote:  Yeah, I saw that 16RX... very drool worthy!  You got a very nice radio there!

Looking at it again reminds me... what's the switch for down at the bottom edge?

The purpose of the switch on the model 16 changed from AVC enable/disable to bass boost in later versions. According to this service hint only the code 121 and 122 had AVC function.

According to this discussion the 16 chairside is either a code 123 (5 bands) or 127 (4 bands) chassis. I can't quite make out the code # on the chassis sticker from the eBay auction - but since it has a horizontal power transformer I believe that should make it a code 127 - and in fact 4 bands.

Either way I'm going to say that switch is for bass boost. Icon_smile
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
RE: My 'new' Philco 630 CSX chairside! - by Nathan Slingerland - 04-24-2016, 06:36 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios