Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 20 Baby Grand Movie Star!
#6

Mike and Bob,
Thanks for the leads. I can't tell if the small knobs in those pics have the hex design on them or fine grooves. I have some with the fine grooves.

Mike,
I don't think it was a krinkle finish originally, but I do think the gold has been on that cabinet a really long time and may be the reason the finish underneath cracked like that. Usually the factory finish doesn't do that with age. Also you can see the wear on the gold finish from using the radio, which tells me it was on there while the radio was still used on a regular basis. Who knows.....
Steve


Messages In This Thread
Philco 20 Baby Grand Movie Star! - by SteveG - 04-24-2016, 08:27 PM
RE: Philco 20 Baby Grand Movie Star! - by morzh - 04-24-2016, 08:46 PM
RE: Philco 20 Baby Grand Movie Star! - by SteveG - 04-25-2016, 12:20 PM
RE: Philco 20 Baby Grand Movie Star! - by KCMike - 04-25-2016, 12:57 PM
RE: Philco 20 Baby Grand Movie Star! - by SteveG - 04-25-2016, 01:09 PM
RE: Philco 20 Baby Grand Movie Star! - by morzh - 04-25-2016, 01:19 PM
RE: Philco 20 Baby Grand Movie Star! - by SteveG - 04-25-2016, 02:03 PM
RE: Philco 20 Baby Grand Movie Star! - by morzh - 04-25-2016, 03:31 PM
RE: Philco 20 Baby Grand Movie Star! - by SteveG - 04-25-2016, 03:40 PM
RE: Philco 20 Baby Grand Movie Star! - by morzh - 04-25-2016, 03:44 PM
RE: Philco 20 Baby Grand Movie Star! - by SteveG - 04-26-2016, 11:39 PM
RE: Philco 20 Baby Grand Movie Star! - by Arran - 04-28-2016, 11:09 PM
RE: Philco 20 Baby Grand Movie Star! - by SteveG - 04-28-2016, 11:35 PM
RE: Philco 20 Baby Grand Movie Star! - by SteveG - 05-05-2016, 11:24 PM
RE: Philco 20 Baby Grand Movie Star! - by SteveG - 05-06-2016, 11:01 AM
RE: Philco 20 Baby Grand Movie Star! - by SteveG - 05-06-2016, 07:28 PM
RE: Philco 20 Baby Grand Movie Star! - by SteveG - 05-06-2016, 08:07 PM
RE: Philco 20 Baby Grand Movie Star! - by SteveG - 05-07-2016, 04:14 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 769 online users. [Complete List]
» 1 Member(s) | 768 Guest(s)
Avatar

>