Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

philco paper capacitors
#13

(04-27-2016, 09:25 PM)morzh Wrote:  Then there is femtofarad, ten to the -15, 1/1000 of the picofarad. Radios dontdeal with that but some devices do. I have a friend who measures those.

And no one needs Attofarads. Icon_smile

Mike;
  A femtofarad sounds like something that one would use in UHF or microwave devices. where a straight lenth of wire is considered a coil, but that's just a guess. Bob Andersen once found a 1/2 picofarad/mmf capacitor inside a TV tuner, someone took a very small ceramic cap and then ground part of it away to get the value.
Regards
Arran


Messages In This Thread
philco paper capacitors - by Up2960 - 04-26-2016, 08:19 PM
RE: philco paper capacitors - by morzh - 04-26-2016, 11:15 PM
RE: philco paper capacitors - by Radioroslyn - 04-27-2016, 12:01 AM
RE: philco paper capacitors - by morzh - 04-27-2016, 09:44 AM
RE: philco paper capacitors - by klondike98 - 04-27-2016, 07:44 AM
RE: philco paper capacitors - by Radioroslyn - 04-27-2016, 10:38 AM
RE: philco paper capacitors - by kiwi_steve - 05-06-2016, 04:17 AM
RE: philco paper capacitors - by mikethedruid - 04-27-2016, 04:01 PM
RE: philco paper capacitors - by morzh - 04-27-2016, 09:25 PM
RE: philco paper capacitors - by Arran - 04-28-2016, 11:03 PM
RE: philco paper capacitors - by Up2960 - 04-27-2016, 07:15 PM
RE: philco paper capacitors - by Radioroslyn - 04-27-2016, 08:14 PM
RE: philco paper capacitors - by Up2960 - 05-07-2016, 05:32 PM
RE: philco paper capacitors - by morzh - 04-27-2016, 09:28 PM
RE: philco paper capacitors - by sam - 04-27-2016, 10:49 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 711 online users. [Complete List]
» 2 Member(s) | 709 Guest(s)
AvatarAvatar

>