Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 4 Vote(s) - 4 Average
  • 1
  • 2
  • 3
  • 4
  • 5

The list of my radio & TV collection!
#76

Before moving on to the story of the radios of the Leningrad plant named Kazitskogo want to talk about the receivers of another manufacturer - Alexandrovsky factory. This company was one of the leaders in the Soviet Union before the war. It was here that the first receivers manufactured top-grade type SVD. The first models of the scheme SVD were exact replicas of American radios RCA -140 offices in simplified form. A pilot batch (200 pieces) was produced at the plant in Leningrad named Kazitskogo. A commercial batch release was planned and started in a factory in Aleksandrovsk. But after one month after the start of production has been stopped - there was an international scandal because of the use of stolen Soviet enterprise technologies and patents from company RCA. The Soviet government had to officially buy the patents and technology at the company's RCA on the production of tubes and radios. Only after that the production of SVD in Aleksandrovsk was resumed, but newer model SVD-1 with the heat of the lamps 6 Volt. To my great regret, the two PRS models are extremely rare and expensive, and I do not have ...

Sorry, photos taken from the Internet ...

               


Messages In This Thread
RE: The list of my radio & TV collection! - by RadioSvit - 04-30-2016, 03:48 PM
I'm still on the floor laughing! - by terrylett - 01-19-2019, 12:58 PM
462ron - by 462ron - 02-16-2022, 10:22 AM
462ron - by 462ron - 03-05-2023, 09:53 AM
462ron - by 462ron - 03-05-2023, 11:15 AM
462ron - by 462ron - 03-06-2023, 09:41 AM
462ron - by 462ron - 01-01-2025, 10:31 AM
462ron - by 462ron - 01-02-2025, 09:10 AM



Users browsing this thread:
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2222 online users. [Complete List]
» 2 Member(s) | 2220 Guest(s)
AvatarAvatar

>