1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
116B (121) won't fly
Danny
Member
***
Posts: 64
Threads: 22
Joined: Oct 2006
City: Acworth State, Province, Country: GA
#6

05-08-2016, 06:43 PM
(05-06-2016, 09:34 AM)Danny Wrote:  
(05-05-2016, 08:28 PM)morzh Wrote:  Try to put some signal through. You could try the IF frequency, see if it is heard.
If your coils are OK, short of oscillator misbehaving you should have it go through.

Thanks, I'll give it a go....

Finally got a chance to get back at this. Shot tone (460Khz) to RF grid good strong tone.
Same goes for 1st Det . Same for 1st I.F. .
It's the 2nd I.F. there is a amplitude issue. Tone yes but very weak.
At 1st Audio great tone and the same with the Dvr.
Question : The 2nd I.F. is weak but only when I connect signal directly to grid
of the 2nd I.F. The stages directly before 2nd I.F. (1st I.F.) I get a good tone. 
I'd think it wouldn't because of the 2nd I.F. stage was almost silent ? I'm going
to take a look at the 2nd I.F. layout for now.  
Thanks for all the assistance...
 
Danny
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
116B (121) won't fly - by Danny - 05-05-2016, 03:09 PM
RE: 116B (121) won't fly - by morzh - 05-05-2016, 03:42 PM
RE: 116B (121) won't fly - by Danny - 05-05-2016, 06:35 PM
RE: 116B (121) won't fly - by morzh - 05-05-2016, 08:28 PM
RE: 116B (121) won't fly - by Danny - 05-06-2016, 09:34 AM
RE: 116B (121) won't fly - by Danny - 05-08-2016, 06:43 PM
RE: 116B (121) won't fly - by Radioroslyn - 05-08-2016, 07:48 PM
RE: 116B (121) won't fly - by Danny - 05-09-2016, 11:10 AM
RE: 116B (121) won't fly - by morzh - 05-09-2016, 11:57 AM
RE: 116B (121) won't fly - by Danny - 05-09-2016, 04:32 PM
RE: 116B (121) won't fly - by morzh - 05-09-2016, 05:52 PM
RE: 116B (121) won't fly - by Danny - 05-10-2016, 11:10 AM
RE: 116B (121) won't fly - by morzh - 05-10-2016, 11:36 AM
RE: 116B (121) won't fly - by Radioroslyn - 05-10-2016, 02:42 PM
RE: 116B (121) won't fly - by Danny - 05-16-2016, 03:41 PM
RE: 116B (121) won't fly - by Danny - 05-20-2016, 10:04 AM
RE: 116B (121) won't fly - by morzh - 05-20-2016, 10:22 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration