1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco Wirewound Resistor Question
morzh
Odobenus rosmarus
******
Posts: 16,507
Threads: 572
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#6

05-18-2016, 10:14 PM
(05-18-2016, 08:02 PM)Geoff Wrote:  Thanks Morzh.  Where did you get your information?  Do you have a scanned Philco parts book that you could share?

No. I just figured that would do.
IIfthe current draw of the whole thing is 100mA (and it is a lot) then the dissipated power of the 100 ohms is 1W and 60 ohm - 0.6W respectively. Double that for margin.
If you want to have more margin, then 3 and 2 Watts respectively.


Ps. Agree with others - very nice looking resistir, why do you not like it?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco Wirewound Resistor Question - by Geoff - 05-18-2016, 06:05 PM
RE: Philco Wirewound Resistor Question - by morzh - 05-18-2016, 07:32 PM
RE: Philco Wirewound Resistor Question - by Geoff - 05-18-2016, 08:02 PM
RE: Philco Wirewound Resistor Question - by morzh - 05-18-2016, 10:14 PM
RE: Philco Wirewound Resistor Question - by gregb - 05-18-2016, 09:44 PM
RE: Philco Wirewound Resistor Question - by Geoff - 05-20-2016, 02:42 PM
RE: Philco Wirewound Resistor Question - by gregb - 05-20-2016, 05:19 PM
RE: Philco Wirewound Resistor Question - by Geoff - 05-21-2016, 02:00 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 691 online users. [Complete List]
» 1 Member(s) | 690 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration