Ron's 2016 Cabinet Work Part I: Bozak E-300
Posts: 2,159
Threads: 158
Joined: Jan 2013
City: Westland, MI
Hello, Ron. Just my observation, but I would use small finish nails to attach the new trim. Use one of the nails itself as a drill bit to pre-drill holes in the trim. Finish the trim, nail it to the cabinets, then gently countersink the nail heads into the trim about a 1/16th of an inch with a small nail set. Fill in the indents with stainable wood filler. Once dry, rub it smooth with 0000 steel wool. You can then apply stain and finish to the filler with a Q-tip. End result should then be almost invisible. Once again, throwing in my two cents worth. By my account, you should have about a buck in pennies by now! Take care, Gary
"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
Messages In This Thread
RE: 2016 Cabinet Work: Bozak E-300 - by GarySP - 07-22-2016, 12:08 PM
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
PT 6 chassis screws size???
|
| Hello bridKarl,
that sounds right or maybe 8/32 .
Sincerely Richardradiorich — 01:00 AM |
|
PT 6 chassis screws size???
|
| Have this done except for missing chassis screws.
It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM |
|
Philco model 38 code 121 not receiving signal.
|
| Hello Stormlord,
Well done on rewinding that coil it turned fairly good for your first one.
Sincerely Richardradiorich — 09:12 PM |
|
Philco model 38 code 121 not receiving signal.
|
| Well here it is. It ain't pretty, but hopefully it'll work.
I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM |
|
Philco 42-345 Restoration/Repair
|
| Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM |
|
Philco 42-345 Restoration/Repair
|
| Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM |
|
Philco model 38 code 121 not receiving signal.
|
| Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM |
|
Testing a speaker and output transformer Trutone A2-G
|
| The equivalent of one short turn is basically the same as that of a shorted load.
If it is the primary's turn, then the ...morzh — 03:53 PM |
|
Testing a speaker and output transformer Trutone A2-G
|
| I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM |
|
Philco model 38 code 121 not receiving signal.
|
| As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM |
|
Who's Online
|
| There are currently no members online. |
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
