1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Help in Identifying radio
Radioroslyn
Phorum Expert
*****
Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa
#10

07-25-2016, 01:51 PM
There's also some chatter about AE being heard on a National SW-3 in the Howland Island too. Before the crash.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Help in Identifying radio - by lgkinney - 07-24-2016, 01:26 AM
RE: Help in Identifying radio - by OldRestorer - 07-24-2016, 08:45 AM
RE: Help in Identifying radio - by klondike98 - 07-24-2016, 08:46 AM
RE: Help in Identifying radio - by lgkinney - 07-24-2016, 06:33 PM
RE: Help in Identifying radio - by klondike98 - 07-24-2016, 07:49 PM
RE: Help in Identifying radio - by Ron Ramirez - 07-24-2016, 08:58 PM
RE: Help in Identifying radio - by lgkinney - 07-27-2016, 02:54 PM
RE: Help in Identifying radio - by klondike98 - 07-24-2016, 09:18 PM
RE: Help in Identifying radio - by lgkinney - 07-27-2016, 02:46 PM
RE: Help in Identifying radio - by Radioroslyn - 07-25-2016, 01:51 PM
RE: Help in Identifying radio - by morzh - 07-25-2016, 02:27 PM
RE: Help in Identifying radio - by Ron Ramirez - 07-26-2016, 12:39 PM
RE: Help in Identifying radio - by klondike98 - 07-27-2016, 03:50 PM
RE: Help in Identifying radio - by lgkinney - 07-27-2016, 04:06 PM
RE: Help in Identifying radio - by klondike98 - 07-27-2016, 04:32 PM
RE: Help in Identifying radio - by GarySP - 07-27-2016, 05:18 PM
RE: Help in Identifying radio - by lgkinney - 07-28-2016, 12:06 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 759 online users. [Complete List]
» 1 Member(s) | 758 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios