Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 70 Lowboy
#1

Asking for a bit of advice on a Philco 70 Lowboy I am going to look at Friday. I've seen this unit before, and even tried to deal on it in the past with no luck. Now the guy is starting to clear out his collection, but sadly, most of the stuff he is parting out as it's worth more and easier to ship that way due to the audiofools out there and people not wanting complete radios. He called me late this afternoon about it, giving me first go at this little console before he turns it into eBay parts fodder.
I know it still has a decent, solid cabinet and is mostly complete except for the power switch knob and the dial esce.. eske... fark.. thingy! Looks like the ball is in my court and I will have to make an offer on the radio. What would be a fair offer to make? Note, this guy is very eBay savvy and knows that the parts would be desirable for someone with a 70 cathedral cabinet. I'll be sure to give it a good look-over, but want to know at least a starting point for an offer. I think it would  be better for it to survive as a complete set instead of parted out and the cabinet tossed into the dumpster.

No matter where you go, there you are.


Messages In This Thread
Philco 70 Lowboy - by Jayce - 08-10-2016, 09:24 PM
RE: Philco 70 Lowboy - by Ron Ramirez - 08-10-2016, 09:55 PM
RE: Philco 70 Lowboy - by morzh - 08-10-2016, 09:59 PM
RE: Philco 70 Lowboy - by Jayce - 08-10-2016, 10:24 PM
RE: Philco 70 Lowboy - by Jayce - 08-12-2016, 01:13 PM
RE: Philco 70 Lowboy - by Jayce - 08-12-2016, 03:28 PM
RE: Philco 70 Lowboy - by Radioroslyn - 08-12-2016, 04:42 PM
RE: Philco 70 Lowboy - by Jayce - 08-12-2016, 07:10 PM
RE: Philco 70 Lowboy - by Radioroslyn - 08-12-2016, 07:35 PM
RE: Philco 70 Lowboy - by Jayce - 08-12-2016, 09:47 PM
RE: Philco 70 Lowboy - by Ron Ramirez - 08-13-2016, 05:43 AM
RE: Philco 70 Lowboy - by Jayce - 08-13-2016, 07:19 AM
RE: Philco 70 Lowboy - by Ron Ramirez - 08-13-2016, 09:21 AM
RE: Philco 70 Lowboy - by Jayce - 08-13-2016, 04:52 PM
RE: Philco 70 Lowboy - by Arran - 08-14-2016, 04:32 AM
RE: Philco 70 Lowboy - by Jayce - 08-14-2016, 05:04 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>