1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
I can't find schematic model 82
Dan Walker
Senior Member
****
Posts: 377
Threads: 105
Joined: Jul 2011
City: Calgary, AB, CA
#5

09-16-2016, 10:43 PM
   I looked up each one of the models suggested and none of them are close to what I have.
   The photos of the cabinet are the same though.
 This radio has
 [left knob]  on/off, volume
[middle knob  Radio/ phono
 [right knob]  tuning.
  the tubes are as follows
 35Y4-----rectifier
50A5------- output
 14A7------1st audio
 14B6------IF amp
 7A8  converter.
  These are on a tube layout on the bottom of the radio.
    So far I am still stumped and I have tried all the places I can think of.
Thanks for the replies, PS KCMike ,,the photo you directed me to has the AM dial on the bottom and mine has the AM dial on the top

Dan     
   Living in Calgary Alberta
(This post was last modified: 09-16-2016, 10:45 PM by Dan Walker. Edit Reason: add information )
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
I can't find schematic model 82 - by Dan Walker - 09-16-2016, 07:32 PM
RE: I can't find schematic model 82 - by KCMike - 09-16-2016, 09:33 PM
RE: I can't find schematic model 82 - by KCMike - 09-16-2016, 09:48 PM
RE: I can't find schematic model 82 - by Dan Walker - 09-16-2016, 10:43 PM
RE: I can't find schematic model 82 - by winniefs - 08-05-2017, 11:29 AM
RE: I can't find schematic model 82 - by winniefs - 08-06-2017, 05:28 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Another amp build - here I go again!
Sweet! I actually have a Dynaco Mark 4 that I had been running with 6L6s with no mods. Seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM

[-]
Who's Online
There are currently 281 online users. [Complete List]
» 1 Member(s) | 280 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration