Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Precision E-200-C
#2

Hi Mike. Do you have a frequency counter? If so you can hook the signal generator to it and check for accuracy of the generator. You probably should replace the electrolytic caps in it.
Other members on here can give you more detailed advice on what you should do.
Here is a video on one very similar to yours that could help you with how they work.

https://www.youtube.com/watch?v=eE7J4Kpbe6w


Messages In This Thread
Precision E-200-C - by Mike L - 09-17-2016, 07:48 PM
RE: Precision E-200-C - by KCMike - 09-17-2016, 09:50 PM
RE: Precision E-200-C - by Bradley Rush - 11-20-2016, 11:33 PM
RE: Precision E-200-C - by Bradley Rush - 11-21-2016, 01:34 AM
RE: Precision E-200-C - by Mike L - 11-21-2016, 08:49 PM
RE: Precision E-200-C - by KCMike - 11-21-2016, 11:44 PM
RE: Precision E-200-C - by Radioroslyn - 11-22-2016, 12:35 AM
RE: Precision E-200-C - by morzh - 11-22-2016, 12:00 PM
RE: Precision E-200-C - by Radioroslyn - 11-22-2016, 02:21 PM
RE: Precision E-200-C - by morzh - 11-22-2016, 02:26 PM
RE: Precision E-200-C - by Radioroslyn - 11-22-2016, 04:00 PM
RE: Precision E-200-C - by morzh - 11-22-2016, 04:10 PM
RE: Precision E-200-C - by Mondial - 11-23-2016, 10:22 PM
RE: Precision E-200-C - by Radioroslyn - 11-24-2016, 09:10 AM
RE: Precision E-200-C - by Mondial - 11-24-2016, 10:34 AM
RE: Precision E-200-C - by Radioroslyn - 11-24-2016, 12:36 PM
RE: Precision E-200-C - by Mike L - 11-26-2016, 05:32 PM
RE: Precision E-200-C - by Mike L - 12-24-2016, 03:40 PM
RE: Precision E-200-C - by Radioroslyn - 12-24-2016, 04:41 PM
RE: Precision E-200-C - by Mike L - 12-24-2016, 05:49 PM
RE: Precision E-200-C - by Radioroslyn - 12-24-2016, 07:06 PM
RE: Precision E-200-C - by Mike L - 12-31-2016, 09:33 AM
RE: Precision E-200-C - by Radioroslyn - 01-01-2017, 12:55 AM
RE: Precision E-200-C - by Mike L - 01-01-2017, 05:27 PM
RE: Precision E-200-C - by JLuke - 07-27-2024, 12:33 PM
RE: Precision E-200-C - by DaleHCook - 07-28-2024, 11:29 AM
RE: Precision E-200-C - by RodB - 07-28-2024, 04:59 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM
Philco model 38 code 121 not receiving signal.
Good news everyone! I think I have found everything I need for rewinding the antenna coil primary. I found some pla...Stormlord5500 — 09:40 AM
Philco Battery-WWII vintage
My younger sister went to SUNY Plattsburg NY, (BS, MS, RN) in the late 1970sabout 10 min from the Northern NY / Canada b...MrFixr55 — 07:59 AM

[-]
Who's Online
There are currently 1758 online users. [Complete List]
» 3 Member(s) | 1755 Guest(s)
AvatarAvatarAvatar

>