Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

NEW: Superior TV-11 Tube Tester
#4

Here is a list of all resistors and their values..

Measured
R1 40K 41.7K Replaced
R2 2 Meg 2.05 Meg
R3 27K 27K
R4 15K 17.5 k Replaced
R5 20K pot 20K
R6 10K pot 10K
R7 330 Ohms 3 Watt 330 Ohms
R8 47K 50.2K Replaced
R9 350 ohms Pot 3 Ohms then after cleaning 5K Replacing

The Replaced resistors were chosen to get exactly the Right ohmage..

The 2 Caps were originally replaced Did not change them..

There was a resistor across the R9 pot from center contact to side that goes to the 4 Position switch measuring 464 Ohms.. It was removed as it didn't do anything..

[Image: http://i292.photobucket.com/albums/mm38/...dquezd.jpg]

Skip...


Messages In This Thread
NEW: Superior TV-11 Tube Tester - by vecher - 09-20-2016, 01:08 PM
RE: NEW: Superior TV-11 Tube Tester - by morzh - 09-20-2016, 01:14 PM
RE: NEW: Superior TV-11 Tube Tester - by vecher - 09-20-2016, 04:13 PM
RE: NEW: Superior TV-11 Tube Tester - by vecher - 09-20-2016, 05:46 PM
RE: NEW: Superior TV-11 Tube Tester - by vecher - 09-22-2016, 04:53 PM
RE: NEW: Superior TV-11 Tube Tester - by vecher - 09-22-2016, 08:45 PM
RE: NEW: Superior TV-11 Tube Tester - by vecher - 09-23-2016, 11:25 PM
RE: NEW: Superior TV-11 Tube Tester - by vecher - 09-24-2016, 08:44 PM
RE: NEW: Superior TV-11 Tube Tester - by vecher - 09-25-2016, 10:28 PM
RE: NEW: Superior TV-11 Tube Tester - by morzh - 09-26-2016, 08:20 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently 950 online users. [Complete List]
» 2 Member(s) | 948 Guest(s)
AvatarAvatar

>