37-93 hot resister

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

37-93 hot resister

philco phan
Member

Posts: 133
Threads: 27
Joined: Aug 2006
City: Roseville,Ca.

#13

08-22-2009, 02:25 PM

yep.
the minimum resistance measured from g3 to ground is wrong,at least should have been 70 ohms,shortest path to ground is the 70 ohm resistor.also lift 70 ohm and 200 ohm resistors at thier junction so that all you are measuring is the 200 ohm and the electrolytic cap,if around 200 the cap is reversed or shorted.
phil

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

37-93 hot resister - by Zapped - 08-20-2009, 03:07 PM

Re: 37-93 hot resister - by philco phan - 08-20-2009, 03:28 PM

Re: 37-93 hot resister - by Zapped - 08-20-2009, 10:53 PM

Re: 37-93 hot resister - by philco phan - 08-21-2009, 10:38 AM

Re: 37-93 hot resister - by Terry Burns - 08-21-2009, 10:57 AM

Re: 37-93 hot resister - by Zapped - 08-21-2009, 03:36 PM

Re: 37-93 hot resister - by philco phan - 08-21-2009, 04:39 PM

Re: 37-93 hot resister - by Zapped - 08-22-2009, 12:09 AM

Re: 37-93 hot resister - by philco phan - 08-22-2009, 12:57 PM

Re: 37-93 hot resister - by Zapped - 08-22-2009, 01:51 PM

Re: 37-93 hot resister - by philco phan - 08-22-2009, 02:07 PM

Re: 37-93 hot resister - by Zapped - 08-22-2009, 02:12 PM

Re: 37-93 hot resister - by philco phan - 08-22-2009, 02:25 PM

Re: 37-93 hot resister - by philco phan - 08-22-2009, 02:34 PM

Re: 37-93 hot resister - by Zapped - 08-22-2009, 03:34 PM

Re: 37-93 hot resister - by philco phan - 08-22-2009, 04:01 PM

Re: 37-93 hot resister - by Zapped - 08-22-2009, 05:50 PM

Re: 37-93 hot resister - by philco phan - 08-22-2009, 07:08 PM

Re: 37-93 hot resister - by Zapped - 08-22-2009, 08:15 PM

Re: 37-93 hot resister - by philco phan - 08-22-2009, 08:26 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

Who's Online

There are currently 662 online users. [Complete List]
» 1 Member(s) | 661 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me