Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

went to Canada and back today.
#9

Oh...yeah. It's a beast.

Another piece of good news, I got it without the tube cage (same perforated sheet metal piece as we see on many tube amps, like Dynaco or Eico). I texted the owners (as they were obviously original owners of that) and they confirmed they have it and asked for my address so they could send it to me. I hope it comes undamaged, though this is not the most important part, still would like to have the complete thing.

Meantime, trying to research a pre-amp for it.

Likely candidates, in the order listed, are

McIntosh C22
Marantz 7C
Dynakit PAS-3X

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
went to Canada and back today. - by morzh - 10-02-2016, 08:53 PM
RE: went to Canada and back today. - by GarySP - 10-02-2016, 09:47 PM
RE: went to Canada and back today. - by morzh - 10-02-2016, 10:13 PM
RE: went to Canada and back today. - by Arran - 10-03-2016, 04:19 AM
RE: went to Canada and back today. - by morzh - 10-03-2016, 12:25 PM
RE: went to Canada and back today. - by morzh - 10-03-2016, 03:13 PM
RE: went to Canada and back today. - by morzh - 10-05-2016, 03:48 PM
RE: went to Canada and back today. - by Arran - 10-07-2016, 03:52 AM
RE: went to Canada and back today. - by morzh - 10-05-2016, 08:54 PM
RE: went to Canada and back today. - by KCMike - 10-05-2016, 09:20 PM
RE: went to Canada and back today. - by morzh - 10-07-2016, 08:21 AM
RE: went to Canada and back today. - by gregb - 10-07-2016, 09:34 AM
RE: went to Canada and back today. - by morzh - 10-07-2016, 04:22 PM
RE: went to Canada and back today. - by morzh - 10-29-2016, 06:57 PM
RE: went to Canada and back today. - by morzh - 10-29-2016, 07:41 PM
RE: went to Canada and back today. - by morzh - 10-30-2016, 02:30 PM
RE: went to Canada and back today. - by morzh - 10-30-2016, 02:31 PM
RE: went to Canada and back today. - by morzh - 10-30-2016, 06:06 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>