Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Zenith 835
#1

Hi gang:

It is Columbus day today in Massachusetts, state Holiday. I am off and though there are a hundred more important things to do around the house I was sorting through some radios......

I have this Zenith     

http://www.radiomuseum.org/r/zenith_high...b835e.html


It will need the selenium rectifier removed, tubes tested, lytictics done, etc......

It should sound nice, however the case has some real wood on the molding but the top and sides are some kinda mystery finish, a 1950's photo finish maybe? The top has a good scrape about a quarter in size. Just really enough to be obvious, a doilly perhaps? Anyway, someone know what this "covering" is. Contact paper could be an improvement!

The fabric front is OK, got cleaned up, this thing has a light in it, H51 on the base and I guess it lights up near one of the controls, although I cant see where the indicator would glow through the fabric, maybe the hole is full of crud. Has a large midrange and 2 tweeters, looks like the quality went in before the name went on, at least the chassis.

I cannot locate my camera either, so I have no photo for you today.

Anybody familiar with one of these sets?

Thanks. 

Paul 

Tubetalk1


Messages In This Thread
Zenith 835 - by Paul Philco322 - 10-10-2016, 12:15 PM
RE: Zenith 835 - by Paul Philco322 - 11-03-2016, 08:43 PM
RE: Zenith 835 - by OldRestorer - 11-04-2016, 06:47 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
462ron
It’s on the bottom of the homepage of our Philcoradio.com homepage! Ron462ron — 07:20 AM
Model 70 Cabinet Trim
Steve might have some trim left. Not sure he is making anything.morzh — 06:12 AM
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM

[-]
Who's Online
There are currently 266 online users. [Complete List]
» 1 Member(s) | 265 Guest(s)
Avatar

>