Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

went to Canada and back today.
#17

When I ordered the C22, 10 days after that the dealer called and said that instead of promised 7-10 days it would take 'till the end of November. I wined a bit and prepared to wait. Even called the factory to make sure it was the case, and they confirmed.
So imagine my amazement when yesterday the dealer called and said the preamp just came through the door.
Friday is my short day and the Red Bank is only 30 minutes away so I picked it up the same day.

Today hooked up as best I could.
Me and my son just finished listening to ZZTOP vinyl. "Los tres hombres".
Geez, you have to know what your pickup type is, moving magnet or coil.

Tomorrow my trusty rack Kenwood system goes to my son's room. He's excited. He knows how to operate it and it is a good sounding system.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
went to Canada and back today. - by morzh - 10-02-2016, 08:53 PM
RE: went to Canada and back today. - by GarySP - 10-02-2016, 09:47 PM
RE: went to Canada and back today. - by morzh - 10-02-2016, 10:13 PM
RE: went to Canada and back today. - by Arran - 10-03-2016, 04:19 AM
RE: went to Canada and back today. - by morzh - 10-03-2016, 12:25 PM
RE: went to Canada and back today. - by morzh - 10-03-2016, 03:13 PM
RE: went to Canada and back today. - by morzh - 10-05-2016, 03:48 PM
RE: went to Canada and back today. - by Arran - 10-07-2016, 03:52 AM
RE: went to Canada and back today. - by morzh - 10-05-2016, 08:54 PM
RE: went to Canada and back today. - by KCMike - 10-05-2016, 09:20 PM
RE: went to Canada and back today. - by morzh - 10-07-2016, 08:21 AM
RE: went to Canada and back today. - by gregb - 10-07-2016, 09:34 AM
RE: went to Canada and back today. - by morzh - 10-07-2016, 04:22 PM
RE: went to Canada and back today. - by morzh - 10-29-2016, 06:57 PM
RE: went to Canada and back today. - by morzh - 10-29-2016, 07:41 PM
RE: went to Canada and back today. - by morzh - 10-30-2016, 02:30 PM
RE: went to Canada and back today. - by morzh - 10-30-2016, 02:31 PM
RE: went to Canada and back today. - by morzh - 10-30-2016, 06:06 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>