Hick 209A VTVM

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Hick 209A VTVM

Bradley Rush
RadioMonkey

Posts: 220
Threads: 56
Joined: Oct 2011
City: Lompoc CA

#17

12-16-2016, 04:57 AM

Thx Mr Mondial no longer is the dial slamming to either side hard. It does tap. The 3 diodes has worked for that. Im thinking of adding another 25v 100uf into the circuit. Because when using ohms to zero it taps. Also when I release from zero. Ohms is working with in 10%. DC is off by 4v. I was measuring direct. No 3.3M resistor. Before I continue with cal. Im putting it all together, replacing last var resistor. What it seems like is the battery acid is still inside the resistors. I will take them apart later.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Hick 209A VTVM - by Bradley Rush - 12-06-2016, 02:41 AM

RE: Hick 209A VTVM - by Bradley Rush - 12-10-2016, 06:10 PM

RE: Hick 209A VTVM - by Bradley Rush - 12-10-2016, 06:12 PM

RE: Hick 209A VTVM - by Bradley Rush - 12-10-2016, 06:14 PM

RE: Hick 209A VTVM - by Bradley Rush - 12-10-2016, 06:16 PM

RE: Hick 209A VTVM - by Bradley Rush - 12-10-2016, 06:19 PM

RE: Hick 209A VTVM - by Bradley Rush - 12-11-2016, 02:52 AM

RE: Hick 209A VTVM - by Bradley Rush - 12-11-2016, 02:54 AM

RE: Hick 209A VTVM - by Bradley Rush - 12-12-2016, 12:31 AM

RE: Hick 209A VTVM - by Bradley Rush - 12-12-2016, 01:05 AM

RE: Hick 209A VTVM - by Mondial - 12-12-2016, 10:05 AM

RE: Hick 209A VTVM - by Bradley Rush - 12-14-2016, 12:29 AM

RE: Hick 209A VTVM - by Mondial - 12-14-2016, 05:58 PM

RE: Hick 209A VTVM - by Bradley Rush - 12-14-2016, 12:59 AM

RE: Hick 209A VTVM - by Bradley Rush - 12-15-2016, 07:04 AM

RE: Hick 209A VTVM - by Bradley Rush - 12-16-2016, 04:29 AM

RE: Hick 209A VTVM - by Bradley Rush - 12-16-2016, 04:57 AM

RE: Hick 209A VTVM - by Bradley Rush - 12-18-2016, 10:34 PM

RE: Hick 209A VTVM - by TV MAN - 12-19-2016, 11:56 AM

RE: Hick 209A VTVM - by Bradley Rush - 12-19-2016, 08:10 PM

RE: Hick 209A VTVM - by TV MAN - 12-20-2016, 09:48 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me