Philco 50 (Nathan's)

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x

Thread Closed

Linear Mode

Philco 50 (Nathan's)

Nathan Slingerland
Super Moderator

Posts: 1,909
Threads: 216
Joined: May 2015
City: Seattle State, Province, Country: WA

#24

12-21-2016, 01:54 AM

Now I'm ready to go through and restuff each bakelite block and replace the out of tolerance resistors.

Several hours later:

[Image: http://i1072.photobucket.com/albums/w374...embucc.jpg]

Wow that wasn't so bad. I tested it at a few intermediate points and managed not to screw anything up...

...that is until I went to align it. The 2nd RF adjustment nut was stuck tight and of course I knew it needed just a bit more torque to loosen it...

[Image: http://i1072.photobucket.com/albums/w374...ue68oh.jpg]

Well that's going to be a bit of a problem. Icon_problem

It looks like the threaded portion is actually a small bolt that has been soldered or welded to the body of the tuning capacitor. So the next step will be to take that off and apart.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Philco 50 (Nathan's) - by Nathan Slingerland - 12-19-2016, 09:37 PM

RE: Philco 50 (Nathan's) - by Nathan Slingerland - 12-19-2016, 09:42 PM

RE: Philco 50 (Nathan's) - by klondike98 - 12-19-2016, 10:10 PM

RE: Philco 50 (Nathan's) - by Nathan Slingerland - 12-20-2016, 12:10 AM

RE: Philco 50 (Nathan's) - by Nathan Slingerland - 12-20-2016, 01:02 AM

RE: Philco 50 (Nathan's) - by Radioroslyn - 12-20-2016, 01:06 AM

RE: Philco 50 (Nathan's) - by Radioroslyn - 12-20-2016, 01:02 AM

RE: Philco 50 (Nathan's) - by Nathan Slingerland - 12-20-2016, 01:05 AM

RE: Philco 50 (Nathan's) - by Radioroslyn - 12-20-2016, 01:09 AM

RE: Philco 50 (Nathan's) - by Nathan Slingerland - 12-20-2016, 01:16 AM

RE: Philco 50 (Nathan's) - by Nathan Slingerland - 12-20-2016, 01:34 AM

RE: Philco 50 (Nathan's) - by Nathan Slingerland - 12-20-2016, 01:47 AM

RE: Philco 50 (Nathan's) - by klondike98 - 12-20-2016, 09:08 AM

RE: Philco 50 (Nathan's) - by TV MAN - 12-20-2016, 11:40 AM

RE: Philco 50 (Nathan's) - by morzh - 12-20-2016, 12:54 PM

RE: Philco 50 (Nathan's) - by Nathan Slingerland - 12-20-2016, 02:00 PM

RE: Philco 50 (Nathan's) - by Ron Ramirez - 12-20-2016, 03:31 PM

RE: Philco 50 (Nathan's) - by Nathan Slingerland - 12-20-2016, 04:43 PM

RE: Philco 50 (Nathan's) - by TV MAN - 12-20-2016, 09:39 PM

RE: Philco 50 (Nathan's) - by Nathan Slingerland - 12-20-2016, 10:28 PM

RE: Philco 50 (Nathan's) - by morzh - 12-21-2016, 12:51 AM

RE: Philco 50 (Nathan's) - by Nathan Slingerland - 12-21-2016, 01:30 AM

RE: Philco 50 (Nathan's) - by Nathan Slingerland - 12-21-2016, 01:47 AM

RE: Philco 50 (Nathan's) - by Nathan Slingerland - 12-21-2016, 01:54 AM

RE: Philco 50 (Nathan's) - by klondike98 - 12-21-2016, 10:21 AM

RE: Philco 50 (Nathan's) - by morzh - 12-21-2016, 12:02 PM

RE: Philco 50 (Nathan's) - by TV MAN - 12-21-2016, 01:05 PM

RE: Philco 50 (Nathan's) - by morzh - 12-21-2016, 02:07 PM

RE: Philco 50 (Nathan's) - by Nathan Slingerland - 12-22-2016, 01:59 AM

RE: Philco 50 (Nathan's) - by Nathan Slingerland - 12-22-2016, 02:09 AM

RE: Philco 50 (Nathan's) - by Nathan Slingerland - 12-23-2016, 01:49 AM

RE: Philco 50 (Nathan's) - by morzh - 12-23-2016, 09:16 AM

RE: Philco 50 (Nathan's) - by Ron Ramirez - 12-23-2016, 09:23 AM

RE: Philco 50 (Nathan's) - by klondike98 - 12-23-2016, 09:48 AM

RE: Philco 50 (Nathan's) - by TV MAN - 12-23-2016, 11:21 AM

RE: Philco 50 (Nathan's) - by Nathan Slingerland - 12-23-2016, 02:07 PM

RE: Philco 50 (Nathan's) - by Ron Ramirez - 12-23-2016, 06:39 PM

RE: Philco 50 (Nathan's) - by Nathan Slingerland - 12-23-2016, 08:17 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
That looks a lot like an aircraft connector of some kind, even if it's a U.S.N power supply. I have a book somewhere abo...Arran — 02:56 AM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
hello david, I have a similar generator in my collection that features a cast iron, single-cylinder Briggs & Stratt...radiorich — 01:00 AM
under chassis parts locator diagram for 1938 Zenith 9s262
Has anyone gone to the trouble of creating an under chassis parts locator image? Yes, I can identify components by foll...bobloney — 08:57 PM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
Try looking at this site the book mark is for a old generator that I was given. David https://radionerds.com/index.ph...David — 08:36 PM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
Hello Everyone, I am looking for voltage identification for all the pin positions on the socket of a CRV-20130 power su...Tonym4704 — 08:16 PM
Philco P45-6365 Universal Transformer Instruction Manual
Can anyone guide me to where this may be found?GRG — 03:00 PM
54C Complete Teardown/Rebuild
I don't think that I have encountered a 12Z3 before, curious how it uses one of those but includes a #43, which is a 25 ...Arran — 02:17 PM
HiFi (Chifi) tube amp build - but my own design.
It's the other forum. I'm also in DIY, but mostly read there. Honestly, I kinda jumped into this without much thought to...TV MAN — 10:43 AM
Philco 71 Code 125
Hello, I am in need of a schematic for this radio. Mine has the three separate circular tube shields and a shadow me...dconant — 08:06 AM
Stromberg Carlson 1500 Squeal
And life just keeps getting more complicated.dconant — 07:57 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me