118X electrical overhaul

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

118X electrical overhaul

Davros
Junior Member

Posts: 8
Threads: 1
Joined: Dec 2016
City: Winston Salem, NC

01-01-2017, 05:09 PM

I read out the speaker, and I believe I may have an issue with the Output transformer.

Reading from terminal to terminal I got the following readings

Two terminals in the green box read 1100 Ohms

Two terminals in the red box read open

Two terminals in the yellow box read .02 ohms (Shorted)

If I am correct and these readings are bad, what are my options?

Attached Files Image(s)

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

118X electrical overhaul - by Davros - 12-29-2016, 10:24 PM

RE: 118X electrical overhaul - by klondike98 - 12-29-2016, 11:54 PM

RE: 118X electrical overhaul - by morzh - 12-30-2016, 12:12 AM

RE: 118X electrical overhaul - by Radioroslyn - 12-30-2016, 02:02 AM

RE: 118X electrical overhaul - by Davros - 12-30-2016, 02:03 PM

RE: 118X electrical overhaul - by morzh - 12-30-2016, 04:40 PM

RE: 118X electrical overhaul - by Davros - 12-30-2016, 07:41 PM

RE: 118X electrical overhaul - by morzh - 12-30-2016, 08:17 PM

RE: 118X electrical overhaul - by Davros - 01-01-2017, 05:09 PM

RE: 118X electrical overhaul - by morzh - 01-01-2017, 05:20 PM

RE: 118X electrical overhaul - by Davros - 01-01-2017, 10:40 PM

RE: 118X electrical overhaul - by morzh - 01-01-2017, 10:49 PM

RE: 118X electrical overhaul - by Radioroslyn - 01-01-2017, 11:10 PM

RE: 118X electrical overhaul - by Davros - 01-02-2017, 07:54 PM

RE: 118X electrical overhaul - by Davros - 01-02-2017, 09:18 PM

RE: 118X electrical overhaul - by Mondial - 01-02-2017, 10:17 PM

RE: 118X electrical overhaul - by morzh - 01-02-2017, 10:17 PM

RE: 118X electrical overhaul - by Davros - 07-17-2017, 05:26 PM

RE: 118X electrical overhaul - by morzh - 07-17-2017, 06:07 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Another amp build - here I go again!
Sweet! I actually have a Dyba Mark 4 that I had been running with 6L6s with no mods. seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM

Who's Online

There are currently 294 online users. [Complete List]
» 1 Member(s) | 293 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me