Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 89 veneer missing
#5

I think that the veneer over the arch is like that on a model 81, it looks like some sort of tight grained, blond, hardwood like maple, poplar, or beech. Knowing Philco that's probably what they used since they intended to slap shaded lacquer over top of it, the fact that it's also a thick veneer would also indicate this. The model 89 was a step up from a model 60, which was a step up from a model 80/81, so they used the fancy veneer on the front panel and used the cheap stuff over the arch, whereas the 80/81s used cheap veneer on everything.
Regards
Arran


Messages In This Thread
Philco 89 veneer missing - by RadioDR401 - 03-07-2017, 09:00 PM
RE: Philco 89 veneer missing - by John Bartley - 03-08-2017, 08:12 AM
RE: Philco 89 veneer missing - by Steve Davis - 03-08-2017, 10:29 AM
RE: Philco 89 veneer missing - by Radioroslyn - 03-10-2017, 09:40 PM
RE: Philco 89 veneer missing - by Arran - 03-13-2017, 01:54 AM
RE: Philco 89 veneer missing - by Steve Davis - 03-13-2017, 10:29 PM
RE: Philco 89 veneer missing - by Arran - 03-13-2017, 10:43 PM
RE: Philco 89 veneer missing - by RadioDR401 - 03-14-2017, 11:42 AM
RE: Philco 89 veneer missing - by Steve Davis - 03-14-2017, 01:27 PM
RE: Philco 89 veneer missing - by Arran - 03-14-2017, 07:50 PM
RE: Philco 89 veneer missing - by RadioDR401 - 07-04-2017, 11:41 AM
RE: Philco 89 veneer missing - by Steve Davis - 07-04-2017, 02:07 PM
RE: Philco 89 veneer missing - by RadioDR401 - 07-05-2017, 04:28 PM
RE: Philco 89 veneer missing - by Phlogiston - 07-05-2017, 06:13 PM
RE: Philco 89 veneer missing - by RadioDR401 - 07-06-2017, 07:18 AM
RE: Philco 89 veneer missing - by Phlogiston - 07-06-2017, 10:33 AM
RE: Philco 89 veneer missing - by RadioDR401 - 08-29-2017, 12:40 PM
RE: Philco 89 veneer missing - by RadioDR401 - 09-09-2017, 03:33 PM
RE: Philco 89 veneer missing - by Phlogiston - 09-09-2017, 04:05 PM
RE: Philco 89 veneer missing - by Scott D - 09-09-2017, 05:15 PM
RE: Philco 89 veneer missing - by RadioDR401 - 03-05-2018, 05:09 PM
RE: Philco 89 veneer missing - by sdradioman - 03-05-2018, 10:07 PM
RE: Philco 89 veneer missing - by Radioroslyn - 03-05-2018, 11:46 PM
RE: Philco 89 veneer missing - by RadioDR401 - 03-06-2018, 10:49 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 744 online users. [Complete List]
» 1 Member(s) | 743 Guest(s)
Avatar

>