Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Need help with Mod. 26J (19/89?)
#2

Can you post a picture of it or the diagram? Without it I'm at a loss.
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Need help with Mod. 26J (19/89?) - by baspas - 12-31-2009, 01:08 AM
Re: Need help with Mod. 26J (19/89?) - by 7estatdef - 12-31-2009, 07:41 AM
Re: Need help with Mod. 26J (19/89?) - by baspas - 12-31-2009, 10:50 AM
Re: Need help with Mod. 26J (19/89?) - by baspas - 01-01-2010, 01:30 PM
Re: Need help with Mod. 26J (19/89?) - by baspas - 01-01-2010, 06:59 PM
Re: Need help with Mod. 26J (19/89?) - by exray - 01-02-2010, 09:19 AM
Re: Need help with Mod. 26J (19/89?) - by baspas - 01-02-2010, 12:05 PM
Re: Need help with Mod. 26J (19/89?) - by baspas - 01-02-2010, 02:32 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
philco predicta
Hi CGL18, First off, welcome to the Philco Phorum. I have not worked on a TV for a while but here are some givens: ...MrFixr55 — 08:22 AM
Another amp build - here I go again!
Sweet! I actually have a Dynaco Mark 4 that I had been running with 6L6s with no mods. Seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM

[-]
Who's Online
There are currently no members online.

>