Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 70
#11

Ok, maybe the osc. coil is defective, but why does it test good and why do I have good grid voltage at all frequencies? I just noticed one other thing. While I have great volume, over the dial, I find that it is slightly difficult to tune in a strong station because the tuning is broad. I can turn the dial through about a 30 Khz range on strong stations. I suspect that the oscillator is working correctly, however maybe not at the correct frequency, because the average super has about -5 to -25 volts on the osc grid. On mine the grid, using a VTVM reads between -21 to -25V throughout the tuning range. Yes, a scope or frequency counter would help, but those I no longer own. The oscillator is definitely working. Correct frequency???


Messages In This Thread
Philco 70 - by Tubesforme - 03-26-2017, 07:22 PM
RE: Philco 70 - by Radioroslyn - 03-26-2017, 08:49 PM
RE: Philco 70 - by Tubesforme - 03-27-2017, 08:31 PM
RE: Philco 70 - by Tubesforme - 03-27-2017, 10:09 PM
RE: Philco 70 - by morzh - 03-26-2017, 08:50 PM
RE: Philco 70 - by Tubesforme - 03-27-2017, 03:15 PM
RE: Philco 70 - by Tubesforme - 03-27-2017, 10:06 PM
RE: Philco 70 - by Radioroslyn - 03-26-2017, 09:43 PM
RE: Philco 70 - by Tubesforme - 03-27-2017, 03:07 PM
RE: Philco 70 - by Tubesforme - 03-27-2017, 03:28 PM
RE: Philco 70 - by Radioroslyn - 03-27-2017, 04:22 PM
RE: Philco 70 - by Tubesforme - 03-27-2017, 05:04 PM
RE: Philco 70 - by Tubesforme - 04-06-2017, 03:02 PM
RE: Philco 70 - by Radioroslyn - 03-27-2017, 05:08 PM
RE: Philco 70 - by Tubesforme - 03-27-2017, 08:26 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Electrolytic restuffing/internals
I don’t have a vise so I had to hold it in my hand. Not optimal but covered up by the hvac tape in the end. I have a few...bridkarl — 11:52 PM
Electrolytic restuffing/internals
Bridkarl A question. For a hacksaw the cut looks a little...jagged. Why?morzh — 11:45 PM
The list of my radio & TV collection!
As usual, an interesting post from you, Peter. This seems to be similar to the RCA 3-BX-671 and the Zenith Transoceanic...MrFixr55 — 11:41 PM
The list of my radio & TV collection!
Hello Peter, Thank you for sharing your new video and looks like your weather is nice their too. it was like 25 Cel...radiorich — 11:05 PM
Electrolytic restuffing/internals
hello bridkarl, I will post some better photos ! Sincerely Richardradiorich — 10:14 PM
Electrolytic restuffing/internals
I just taped the two pieces of the cap together, but I can see your method is better. I just held the lead in with solde...bridkarl — 08:18 PM
Electrolytic restuffing/internals
hello bridkarl, Well done ! Here is a Photo of the base of Philco capacitor that I cut open you can see how I glued th...radiorich — 08:14 PM
philco predicta
Hi CGL18, Here is a link for the schematic from the Early television Foundation: WARNING!! One side of the Chassis i...MrFixr55 — 08:09 PM
The list of my radio & TV collection!
Peter; I like Canadian General Electric sets, whilst the model numbers are often the same as their U.S General Electr...Arran — 05:44 PM
Electrolytic restuffing/internals
Did as suggested. Cut can with hacksaw, removed internals, attached new 8mf cap - with ample use of cardboard and elec...bridkarl — 03:36 PM

[-]
Who's Online
There are currently no members online.

>