Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

41-280, need help with tube ID
#2

Elrick, the tube cross reference at Nostalgia Air http://www.nostalgiaair.org/Tubes/ gives only the 42 as a substitute for the 41. I've ordered several 41 tubes in ST style from Antique Electronic Supply or other tube vendors. AES list some NOS and used 41 tubes at their site now.

Vacuum Tubes, Inc says "The 6K6 is the octal equivalent." Obviously the octal tube won't fit in your 6 pin socket.

Why are you looking for a cross-reference? Are your 41s bad?

How far along are you in the restoration? Until you have recapped and rewired the radio, and cleaned the band switch, I doubt if you could be sure the tubes are bad unless they're broken or something. The main thing is to replace all electrolytic and wax capacitors and replace all the rubber-insulated wire before turning the radio on to see if the tubes work. They probably do.

John Honeycutt


Messages In This Thread
41-280, need help with tube ID - by Elrick - 01-14-2010, 04:06 PM
Re: 41-280, need help with tube ID - by Raleigh - 01-14-2010, 05:40 PM
Re: 41-280, need help with tube ID - by Elrick - 01-14-2010, 06:55 PM
Re: 41-280, need help with tube ID - by Raleigh - 01-15-2010, 10:45 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
My collection presentation
There is an article on my site that introduces the first portable radios in my collection. I have only provided a link t...Vlad95 — 01:17 PM
Electrolytic restuffing/internals
Bridkarl This specific cap you have is the easiset type to restuff. I usually cut it at the upper border of the depr...morzh — 11:35 AM
philco predicta
Hi CGL18, First off, welcome to the Philco Phorum. I have not worked on a TV for a while but here are some givens: ...MrFixr55 — 08:22 AM
Another amp build - here I go again!
Sweet! I actually have a Dynaco Mark 4 that I had been running with 6L6s with no mods. Seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM

[-]
Who's Online
There are currently 914 online users. [Complete List]
» 2 Member(s) | 912 Guest(s)
AvatarAvatar

>