Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x

Thread Closed

41-280, need help with tube ID
#3

Raleigh, thanks for the repy. Not sure if my 41 's are bad because I have not been able to find a place that can test them. So far I've only found 1 shop that has a tube tester and it's pretty small and it doesn't accept the 6 pin socket. They did test the Loctal tubes and they ranged from about 45% - 65% good. The 41's may be fine, just wanted to get some information in case I had to order them. I have looked in a few places and didn't see any 41's listed. I'll do a re-cap job, check the resistors and replace the power cord then install the tubes and power her up. On the good side I don't seem to have the crumbling wire insulation that many have written about. Radio is complete, inside loop antenna and speaker are in decent shape cabinet has some scratches and dings but not too bad. I remember as a kid playing with the push buttons and sticking pointy things in the plastic over the station call letter windows. Later.


Messages In This Thread
41-280, need help with tube ID - by Elrick - 01-14-2010, 04:06 PM
Re: 41-280, need help with tube ID - by Raleigh - 01-14-2010, 05:40 PM
Re: 41-280, need help with tube ID - by Elrick - 01-14-2010, 06:55 PM
Re: 41-280, need help with tube ID - by Raleigh - 01-15-2010, 10:45 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
That looks a lot like an aircraft connector of some kind, even if it's a U.S.N power supply. I have a book somewhere abo...Arran — 02:56 AM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
hello david, I have a similar generator in my collection that features a cast iron, single-cylinder Briggs & Stratt...radiorich — 01:00 AM
under chassis parts locator diagram for 1938 Zenith 9s262
Has anyone gone to the trouble of creating an under chassis parts locator image?  Yes, I can identify components by foll...bobloney — 08:57 PM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
Try looking at this site the book mark is for a old generator that I was given. David    https://radionerds.com/index.ph...David — 08:36 PM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
Hello Everyone, I am looking for voltage identification for all the pin positions on the socket of a CRV-20130 power su...Tonym4704 — 08:16 PM
Philco P45-6365 Universal Transformer Instruction Manual
Can anyone guide me to where this may be found?GRG — 03:00 PM
54C Complete Teardown/Rebuild
I don't think that I have encountered a 12Z3 before, curious how it uses one of those but includes a #43, which is a 25 ...Arran — 02:17 PM
HiFi (Chifi) tube amp build - but my own design.
It's the other forum. I'm also in DIY, but mostly read there. Honestly, I kinda jumped into this without much thought to...TV MAN — 10:43 AM
Philco 71 Code 125
Hello,  I am in need of a schematic for this radio. Mine has the three separate circular tube shields and a shadow me...dconant — 08:06 AM
Stromberg Carlson 1500 Squeal
And life just keeps getting more complicated.dconant — 07:57 AM

[-]
Who's Online
There are currently no members online.

>