Philco 40-165

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 40-165

morzh
Odobenus rosmarus

Posts: 16,509
Threads: 572
Joined: Oct 2011
City: Jackson State, Province, Country: NJ

#11

06-07-2017, 10:42 AM

This is the Push-Pull transformer. You need a Single-Ended (SE) transformer.

125CSE by Hammond is the one you might want. But it is expensive.

Your connections will be primary - only one way and the secondary - BLK to ORG/GRN for 4/8 Ohm

http://www.ebay.com/itm/240012-Tube-Audi...SwRUhY9jyc
http://www.ebay.com/itm/tested-tube-amp-...SwlndZCoDF
(these two do not say if it is P-P or SE type, nor do I think they have documentation with them - you could ask)

http://www.ebay.com/itm/OT10SE-USA-Singl...xy2E1SEY30

http://www.ebay.com/itm/OT8SE-Single-End...SwgNRV8Oov
(my favorite - you have to see if the size fits).

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Philco 40-165 - by jmcgill - 06-02-2017, 08:10 PM

RE: Philco 40-165 - by Radioroslyn - 06-03-2017, 04:42 AM

RE: Philco 40-165 - by jmcgill - 06-04-2017, 05:13 PM

RE: Philco 40-165 - by Radioroslyn - 06-05-2017, 10:45 AM

RE: Philco 40-165 - by jmcgill - 06-05-2017, 01:42 PM

RE: Philco 40-165 - by morzh - 06-05-2017, 02:04 PM

RE: Philco 40-165 - by Radioroslyn - 06-05-2017, 04:05 PM

RE: Philco 40-165 - by jmcgill - 06-06-2017, 01:40 PM

RE: Philco 40-165 - by Radioroslyn - 06-06-2017, 04:12 PM

RE: Philco 40-165 - by jmcgill - 06-07-2017, 09:46 AM

RE: Philco 40-165 - by morzh - 06-07-2017, 10:42 AM

RE: Philco 40-165 - by Radioroslyn - 06-07-2017, 01:22 PM

RE: Philco 40-165 - by Ron Ramirez - 06-11-2017, 11:00 AM

RE: Philco 40-165 - by Radioroslyn - 06-11-2017, 11:14 AM

RE: Philco 40-165 - by jmcgill - 06-11-2017, 03:20 PM

RE: Philco 40-165 - by Radioroslyn - 06-11-2017, 04:03 PM

RE: Philco 40-165 - by jmcgill - 07-26-2017, 06:46 PM

RE: Philco 40-165 - by Radioroslyn - 07-26-2017, 07:26 PM

40-165 - by jmcgill - 06-11-2017, 09:45 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Another amp build - here I go again!
Sweet! I actually have a Dynaco Mark 4 that I had been running with 6L6s with no mods. Seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM

Who's Online

There are currently 256 online users. [Complete List]
» 2 Member(s) | 254 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me