Philco 40-165

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 40-165

jmcgill
Junior Member

Posts: 8
Threads: 1
Joined: May 2017
City: Germanton, NC

#16

06-11-2017, 03:20 PM

Once again your expertise is invaluable.
The power transformer secondary resistance reads a little low. The schematic has half the secondary at 420 ohms and the other half at 400 ohms. I get about 300 ohms on one side and about 345 ohms on the other. The primary reads 18 ohms just as the schematic says it should and the filament windings read <.1 ohm. Should it be replaced or is it within tolerance?

Einstein once said, "I have no special talents, I am only passionately curious."

Jim

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Philco 40-165 - by jmcgill - 06-02-2017, 08:10 PM

RE: Philco 40-165 - by Radioroslyn - 06-03-2017, 04:42 AM

RE: Philco 40-165 - by jmcgill - 06-04-2017, 05:13 PM

RE: Philco 40-165 - by Radioroslyn - 06-05-2017, 10:45 AM

RE: Philco 40-165 - by jmcgill - 06-05-2017, 01:42 PM

RE: Philco 40-165 - by morzh - 06-05-2017, 02:04 PM

RE: Philco 40-165 - by Radioroslyn - 06-05-2017, 04:05 PM

RE: Philco 40-165 - by jmcgill - 06-06-2017, 01:40 PM

RE: Philco 40-165 - by Radioroslyn - 06-06-2017, 04:12 PM

RE: Philco 40-165 - by jmcgill - 06-07-2017, 09:46 AM

RE: Philco 40-165 - by morzh - 06-07-2017, 10:42 AM

RE: Philco 40-165 - by Radioroslyn - 06-07-2017, 01:22 PM

RE: Philco 40-165 - by Ron Ramirez - 06-11-2017, 11:00 AM

RE: Philco 40-165 - by Radioroslyn - 06-11-2017, 11:14 AM

RE: Philco 40-165 - by jmcgill - 06-11-2017, 03:20 PM

RE: Philco 40-165 - by Radioroslyn - 06-11-2017, 04:03 PM

RE: Philco 40-165 - by jmcgill - 07-26-2017, 06:46 PM

RE: Philco 40-165 - by Radioroslyn - 07-26-2017, 07:26 PM

40-165 - by jmcgill - 06-11-2017, 09:45 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Another amp build - here I go again!
Sweet! I actually have a Dyba Mark 4 that I had been running with 6L6s with no mods. seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me