Eico Model 315 SG

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Eico Model 315 SG

Radioroslyn
Phorum Expert

Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa

#13

06-23-2017, 11:51 PM

Is the F band adjustment the trimmer next the toggle sw?? If so give it a shot of deoxit spin it around a couple of times and let it dry out for while. Then give it a try. If that doesn't do it try compressing the coil just a little. Seems like your osc doesn't have enough feedback.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Eico Model 315 SG - by vecher - 06-15-2017, 11:58 PM

RE: Eico Model 315 SG - by Radioroslyn - 06-16-2017, 12:48 AM

RE: Eico Model 315 SG - by vecher - 06-16-2017, 04:51 PM

RE: Eico Model 315 SG - by vecher - 06-16-2017, 07:19 PM

RE: Eico Model 315 SG - by Eliot Ness - 06-16-2017, 09:49 PM

RE: Eico Model 315 SG - by vecher - 06-16-2017, 10:45 PM

RE: Eico Model 315 SG - by Radioroslyn - 06-16-2017, 10:54 PM

RE: Eico Model 315 SG - by vecher - 06-16-2017, 10:59 PM

RE: Eico Model 315 SG - by vecher - 06-19-2017, 12:31 AM

RE: Eico Model 315 SG - by vecher - 06-22-2017, 11:15 PM

RE: Eico Model 315 SG - by Radioroslyn - 06-23-2017, 01:37 AM

RE: Eico Model 315 SG - by vecher - 06-23-2017, 11:03 PM

RE: Eico Model 315 SG - by Radioroslyn - 06-23-2017, 11:51 PM

RE: Eico Model 315 SG - by vecher - 06-24-2017, 12:33 AM

RE: Eico Model 315 SG - by vecher - 06-24-2017, 09:37 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

Who's Online

There are currently 981 online users. [Complete List]
» 1 Member(s) | 980 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me