Eico Model 315 SG

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Eico Model 315 SG

vecher
Phorum Expert

Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA

#15

06-24-2017, 09:37 PM

Ok, Tried all of that same problem..I even replaced the trimmer and coil from a parts set same problem.. however I was able to get down to about 20 mhz before I lost signal..I tried to measure the grid of the OSC Tube pin 6 says it should be -.6 volts I get -.04 volts..

When I go to other bands I get over -6 volts up to about -20 volts on band A..

PS Ready to give up on this.. All other bands work good...

Skip...

(This post was last modified: 06-24-2017, 09:40 PM by vecher.)

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Eico Model 315 SG - by vecher - 06-15-2017, 11:58 PM

RE: Eico Model 315 SG - by Radioroslyn - 06-16-2017, 12:48 AM

RE: Eico Model 315 SG - by vecher - 06-16-2017, 04:51 PM

RE: Eico Model 315 SG - by vecher - 06-16-2017, 07:19 PM

RE: Eico Model 315 SG - by Eliot Ness - 06-16-2017, 09:49 PM

RE: Eico Model 315 SG - by vecher - 06-16-2017, 10:45 PM

RE: Eico Model 315 SG - by Radioroslyn - 06-16-2017, 10:54 PM

RE: Eico Model 315 SG - by vecher - 06-16-2017, 10:59 PM

RE: Eico Model 315 SG - by vecher - 06-19-2017, 12:31 AM

RE: Eico Model 315 SG - by vecher - 06-22-2017, 11:15 PM

RE: Eico Model 315 SG - by Radioroslyn - 06-23-2017, 01:37 AM

RE: Eico Model 315 SG - by vecher - 06-23-2017, 11:03 PM

RE: Eico Model 315 SG - by Radioroslyn - 06-23-2017, 11:51 PM

RE: Eico Model 315 SG - by vecher - 06-24-2017, 12:33 AM

RE: Eico Model 315 SG - by vecher - 06-24-2017, 09:37 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

Who's Online

There are currently 2268 online users. [Complete List]
» 1 Member(s) | 2267 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me