1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Newbie with a 42-360 question
klondike98
Phorum Moderator
******
Posts: 5,170
Threads: 274
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#3

07-07-2017, 09:11 AM
Pointers can be a little tough to find. Usually folks are selling the entire chassis although occasionally on ebay someone will part out a set in some fashion. As morzh mentioned you may be able to fashion one for the time being.

Put a request in the "Wanted Ads" section of the Phorum and you may find that someone has something in their junk parts box that will work for you.

Welcome to the Phorum!
Icon_wave
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Newbie with a 42-360 question - by duckieduckie - 07-07-2017, 04:41 AM
RE: Newbie with a 42-360 question - by morzh - 07-07-2017, 08:00 AM
RE: Newbie with a 42-360 question - by klondike98 - 07-07-2017, 09:11 AM
RE: Newbie with a 42-360 question - by morzh - 07-07-2017, 09:16 AM
RE: Newbie with a 42-360 question - by klondike98 - 07-07-2017, 09:17 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Another amp build - here I go again!
Sweet! I actually have a Dyba Mark 4 that I had been running with 6L6s with no mods. seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM

[-]
Who's Online
There are currently 293 online users. [Complete List]
» 1 Member(s) | 292 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration