Philco model 84B Cap ?

Register

Guest Join Us

Hello Guest,

Please feel free to join us!
There are many more parts of the Phorum that only members can see.

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco model 84B Cap ?

Eric
Senior Member

Posts: 451
Threads: 85
Joined: Nov 2011
City: Cumming, GA

#6

07-09-2017, 03:36 PM

Had #20 wired wrong went and did it per your drawing and verified it through the schematic. The person before me just added caps on top of the filter caps without disconnecting them from the old. They also just added caps on top of the bakelite blocks so is was quite a rats nest.
The tubes all check good and the voltages look good and I'm using about 30' on antenna and I get the 2 big stations here in the Atlanta area. Next up is an alignment.

Thanks for the help!

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco model 84B Cap ? - by Eric - 07-07-2017, 12:33 PM

RE: Philco model 84B Cap ? - by WallaceRoger - 07-07-2017, 01:51 PM

RE: Philco model 84B Cap ? - by Eric - 07-07-2017, 02:25 PM

RE: Philco model 84B Cap ? - by klondike98 - 07-07-2017, 03:16 PM

RE: Philco model 84B Cap ? - by Radioroslyn - 07-07-2017, 03:20 PM

RE: Philco model 84B Cap ? - by Eric - 07-09-2017, 03:36 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Another amp build - here I go again!
Sweet! I actually have a Dyba Mark 4 that I had been running with 6L6s with no mods. seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM

Who's Online
There are currently no members online.