Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Crosley Bandbox 601 / What could go wrong??
#1

So a couple of years ago I picked up a Crosley Bandbox aka model 601. Tiz a battery set from about 1927-28. I don't know why I guess I felt sorry for it. Metal case was pretty good but inside was a different story. Internet image:
[Image: https://i.ebayimg.com/images/g/uugAAOSwh...s-l300.jpg]

After some disassembly I found that pretty much all of the pot metal parts were kaput!! Tuning caps dial drive and such badly disfigured.
So does this poor little guy have a chance??? Is it curtains for the Crosley???
While I'm mulling it over I gave the tuning cap cover a coat of copper hammertone paint after removing the rust.
Tune in for the next installment.


Attached Files Image(s)
           

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Crosley Bandbox 601 / What could go wrong?? - by Radioroslyn - 08-22-2017, 04:53 PM
RE: What could go wrong??? - by OldRestorer - 08-22-2017, 06:00 PM
RE: What could go wrong??? - by Radioroslyn - 08-22-2017, 06:05 PM
RE: What could go wrong??? - by sam - 08-22-2017, 09:15 PM
RE: What could go wrong??? - by OldRestorer - 08-22-2017, 10:36 PM
RE: What could go wrong??? - by sam - 08-22-2017, 11:53 PM
RE: What could go wrong??? - by Eliot Ness - 08-23-2017, 08:41 AM
RE: What could go wrong??? - by Radioroslyn - 08-23-2017, 12:31 PM
RE: What could go wrong??? - by morzh - 08-23-2017, 12:51 PM
RE: What could go wrong??? - by klondike98 - 08-23-2017, 01:20 PM
RE: What could go wrong??? - by WallaceRoger - 08-23-2017, 02:25 PM
RE: What could go wrong??? - by Radioroslyn - 08-23-2017, 02:46 PM
RE: What could go wrong??? - by Radioroslyn - 08-23-2017, 06:32 PM
RE: What could go wrong??? - by OldRestorer - 08-23-2017, 07:36 PM
RE: What could go wrong??? - by WallaceRoger - 08-24-2017, 10:05 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
462ron
It’s on the bottom of the homepage of our Philcoradio.com homepage! Ron462ron — 07:20 AM
Model 70 Cabinet Trim
Steve might have some trim left. Not sure he is making anything.morzh — 06:12 AM
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM

[-]
Who's Online
There are currently 246 online users. [Complete List]
» 1 Member(s) | 245 Guest(s)
Avatar

>