Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

38-690 Back Cover
#15

(07-10-2016, 02:09 PM)Ron Ramirez Wrote:  Eddie's on Facebook, and he may not be participating on any online forums anymore. I don't know since I am no longer on Facebook.

I had a part of an old back with the artwork. Back when all of this was happening, Eddie asked me if I had the artwork. I scanned it and sent the scan to him and he cleaned it up, used newer fonts to replace the hard to read type, etc.

Ron,
Do you still have those scans? I sure could use them for recreating the logo for a replacement back for my 38-1XX.
Any help appreciated! Icon_biggrin

Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning


Messages In This Thread
38-690 Back Cover - by Jim - 07-07-2016, 12:21 AM
RE: 38-690 Back Cover - by KCMike - 07-07-2016, 07:38 AM
RE: 38-690 Back Cover - by klondike98 - 07-07-2016, 08:16 AM
RE: 38-690 Back Cover - by sam - 07-07-2016, 12:22 PM
RE: 38-690 Back Cover - by jerryhawthorne - 07-07-2016, 05:00 PM
RE: 38-690 Back Cover - by gregb - 07-07-2016, 05:48 PM
RE: 38-690 Back Cover - by jerryhawthorne - 07-07-2016, 06:35 PM
RE: 38-690 Back Cover - by Ron Ramirez - 07-07-2016, 08:20 PM
RE: 38-690 Back Cover - by Paul Philco322 - 07-10-2016, 11:07 AM
RE: 38-690 Back Cover - by gregb - 07-10-2016, 11:23 AM
RE: 38-690 Back Cover - by jerryhawthorne - 07-10-2016, 01:47 PM
RE: 38-690 Back Cover - by sam - 07-10-2016, 01:53 PM
RE: 38-690 Back Cover - by Ron Ramirez - 07-10-2016, 02:09 PM
RE: 38-690 Back Cover - by sam - 07-10-2016, 06:53 PM
RE: 38-690 Back Cover - by PhilcoPhan1936 - 09-22-2017, 11:09 PM
RE: 38-690 Back Cover - by Ron Ramirez - 09-23-2017, 07:19 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 650 online users. [Complete List]
» 1 Member(s) | 649 Guest(s)
Avatar

>