Weller pencil iron

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Weller pencil iron

Welder
Junior Member

Posts: 41
Threads: 3
Joined: Jan 2017
City: East Brunswick, NJ

11-21-2017, 08:16 PM

Nice pics Terry. I also have a similar Weller with the three Led's. I lost the little set screw but shorten one I bought at Home Depot. Nice job with the Tap &Die. I see you take care of your tools. I have a radial arm saw that dates back to the early 80's and still cuts very good. My first power tool was a B&D corded 3/8' drill which I still have from 1975.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Weller pencil iron - by Radioroslyn - 07-06-2017, 01:44 PM

RE: Weller pencil iron - by klondike98 - 07-06-2017, 02:48 PM

RE: Weller pencil iron - by morzh - 07-06-2017, 03:22 PM

RE: Weller pencil iron - by Radioroslyn - 07-06-2017, 03:53 PM

RE: Weller pencil iron - by morzh - 07-06-2017, 04:38 PM

RE: Weller pencil iron - by sam - 07-06-2017, 07:21 PM

RE: Weller pencil iron - by Radioroslyn - 07-06-2017, 07:31 PM

RE: Weller pencil iron - by Welder - 11-21-2017, 08:16 PM

RE: Weller pencil iron - by Radioroslyn - 11-21-2017, 10:30 PM

RE: Weller pencil iron - by radiohenry - 11-24-2017, 10:28 AM

RE: Weller pencil iron - by Ron Ramirez - 11-25-2017, 11:14 PM

RE: Weller pencil iron - by David - 11-27-2017, 07:08 PM

RE: Weller pencil iron - by WallaceRoger - 12-04-2017, 12:29 PM

RE: Weller pencil iron - by Kenneth F. Besso Jr. - 12-04-2017, 08:41 PM

RE: Weller pencil iron - by jcassity - 07-15-2018, 10:04 PM

RE: Weller pencil iron - by Arran - 07-16-2018, 05:08 AM

RE: Weller pencil iron - by Radioroslyn - 07-16-2018, 09:06 AM

RE: Weller pencil iron - by 35Z5 - 07-16-2018, 09:51 AM

RE: Weller pencil iron - by codefox1 - 07-16-2018, 03:16 PM

RE: Weller pencil iron - by Radioroslyn - 07-16-2018, 08:44 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

Who's Online

There are currently 951 online users. [Complete List]
» 2 Member(s) | 949 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me