1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
38-116 updated it works!!!!
hotrod
Junior Member
**
Posts: 32
Threads: 2
Joined: Apr 2010
#15

05-06-2010, 01:26 AM
Hi Ron,
Got your email today and the PT 41 pack and ready to ship.

I didn't get much done on the 38-116 today because of schoolwork but I did ohm out the power transformer and everything looked good Icon_biggrin I think I got the worst of it licked now I only have 6 or 7 paper caps to replace on the on the Small RF chassis and then finish stuffing one can cap with two 22uf in parallel for the 500V rated caps (Caps 141 4Vand 142). I think I have room to mount a terminal strip for cap 140,140A, 80, 80A, and 80B. I have a 10uf at 500V for 140(the original is 475V) and I think I can get away with 450V caps for the others even though 80 and 80A are rated at 475V.

Rod
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
38-116 updated it works!!!! - by hotrod - 05-01-2010, 03:28 PM
Re: 38-116 IF transformer question - by hotrod - 05-01-2010, 07:55 PM
Re: 38-116 IF transformer question - by hotrod - 05-02-2010, 06:12 PM
Re: 38-116 IF transformer question - by hotrod - 05-02-2010, 08:28 PM
Re: 38-116 IF transformer (new question Output transformer) - by hotrod - 05-06-2010, 01:26 AM
Re: 38-116 updated it works!!!! - by Ron Ramirez - 05-25-2010, 09:31 PM
Re: 38-116 updated it works!!!! - by hotrod - 05-25-2010, 10:33 PM
Re: 38-116 (It Rocks) - by hotrod - 05-31-2010, 06:36 AM
Re: 38-116 updated it works!!!! - by Ron Ramirez - 05-31-2010, 07:50 AM
Re: 38-116 updated it works!!!! - by hotrod - 05-31-2010, 05:08 PM
Re: 38-116 updated it works!!!! - by radiomikee - 06-06-2010, 09:49 PM
Re: 38-116 updated it works!!!! - by hotrod - 06-08-2010, 02:01 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration