38-1 grille cloth

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

38-1 grille cloth

Electrothaumaturgist
Senior Member

Posts: 481
Threads: 18
Joined: Jan 2013
City: Mesa, AZ

#13

03-04-2018, 03:51 PM

Thanks so much guys! It's hard to tell from the image, but all of the Chevron lines wind up exactly even at the corners and in the center rungs. That was the most difficult part of all. Right now I could pull it again and realign it, but that will have to wait for round two... In about 10 years! Icon_lol

I can live with it for now...

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

38-1 grille cloth - by Electrothaumaturgist - 01-26-2018, 10:38 PM

RE: 38-1 grille cloth - by Ron Ramirez - 01-26-2018, 11:35 PM

RE: 38-1 grille cloth - by Electrothaumaturgist - 01-27-2018, 12:14 AM

RE: 38-1 grille cloth - by Electrothaumaturgist - 02-02-2018, 09:27 PM

RE: 38-1 grille cloth - by Electrothaumaturgist - 03-01-2018, 05:27 PM

RE: 38-1 grille cloth - by Ron Ramirez - 03-01-2018, 07:11 PM

RE: 38-1 grille cloth - by Electrothaumaturgist - 03-01-2018, 07:56 PM

RE: 38-1 grille cloth - by Electrothaumaturgist - 03-02-2018, 06:45 PM

RE: 38-1 grille cloth - by Ron Ramirez - 03-02-2018, 07:12 PM

RE: 38-1 grille cloth - by Electrothaumaturgist - 03-02-2018, 07:53 PM

RE: 38-1 grille cloth - by Brad Winder - 03-04-2018, 01:46 PM

RE: 38-1 grille cloth - by Kenneth F. Besso Jr. - 03-04-2018, 02:35 PM

RE: 38-1 grille cloth - by Electrothaumaturgist - 03-04-2018, 03:51 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me