1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
38-7 Cabinet Restoration
Arran
Phorum Expert
*****
Posts: 4,894
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
#10

03-04-2018, 06:20 PM
I think that the two cam shaped bits of hardware may have been left over from when the radio was originally shipped, the base of the radio was probably attached to a board or the bottom of a crate. To me they look kind of like smaller versions of those latches they used to use on wooden sash windows to lock the two sashes together, the cam piece would rotate and feed into a slotted piece of hardware on the other sash. 
Regards
Arran
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
38-7 Cabinet Restoration - by Crist Rigotti - 02-27-2018, 04:41 PM
RE: 38-7 Cabinet Restoration - by cpollock - 02-27-2018, 06:37 PM
RE: 38-7 Cabinet Restoration - by PhilcoPhan1936 - 02-27-2018, 09:37 PM
RE: 38-7 Cabinet Restoration - by cpollock - 02-27-2018, 09:53 PM
RE: 38-7 Cabinet Restoration - by Crist Rigotti - 02-27-2018, 10:29 PM
RE: 38-7 Cabinet Restoration - by Crist Rigotti - 02-27-2018, 11:01 PM
RE: 38-7 Cabinet Restoration - by Crist Rigotti - 03-01-2018, 02:17 AM
RE: 38-7 Cabinet Restoration - by cpollock - 03-03-2018, 09:25 PM
RE: 38-7 Cabinet Restoration - by Arran - 03-04-2018, 06:20 PM
RE: 38-7 Cabinet Restoration - by cpollock - 03-04-2018, 06:34 PM
RE: 38-7 Cabinet Restoration - by Crist Rigotti - 03-05-2018, 01:38 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 661 online users. [Complete List]
» 1 Member(s) | 660 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration