Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Identifying a Model 16 console chassis.....
#1

I know....sounds weird doesn't it?

The above radio was given to me or it would've had a date with a landfill if I didn't take it. The label says "16" but the chassis has yet to be found in my Rider books. I emailed Chuck Schwark and I'm awaiting a reply from him. But I figured I'd throw it out to the mavens on this site and possibly get a few answers...

This circuit is very similiar to the first 16 shown in Nastalgia Air here....

http://www.nostalgiaair.org/pagesbymodel...013139.pdf

With the exception of part 75 e-cap (which was never present on my chassis and the value is not known) and that the two other e-caps (87 and 88) in the lower right hand corner of the chassis are a bit different also. One e-cap (87) seems correct but the other (88) is a two-section cap in my chassis but is notated as a one section ecap on the print. 

In another print, Model 16 Code 125 and 126, part number 91 is shown as a 2 section cap while 98 is shown as a single cap. The non existant ecap on my chassis (75) in the earlier print is now notated as part 73 and is a 4 section cap. See here....

http://www.nostalgiaair.org/pagesbymodel...013141.pdf

I hope I've explained this well enough. I doubt if there is no print for this particular chassis it's just that I haven't found it yet. And yes, the radio works very well on all bands but the power supply, as it exists now, is slowly shorting out. (typical) 13 Boats to restore....this one's gonna take a while.

Thanks for the input....
Jim Koehler

Good luck with the project and all of us here are expecting a full report when you're finished.


Messages In This Thread
Identifying a Model 16 console chassis..... - by Jim Koehler - 08-24-2018, 10:02 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM
Part numbers to model cross
Jim, We have this index put together by Dale Cook but I don't think that is quite what you are looking for. The Parts...klondike98 — 09:37 PM
Philco Model 38-7: what caps & resistors do fail typically?
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM
Philco 42-345 Restoration/Repair
The resistor is a 2.2 Meg, it was the last one I hadn't replaced. The broadcast is coming in after replacing it.osanders0311 — 09:09 PM
Philco 42-345 Restoration/Repair
What does the resistor measure? I think it should be 3.3 Meg. If the oscillator coil has continuity and the resistanc...RodB — 09:03 PM
Philco Model 38-7: what caps & resistors do fail typically?
Good idea to check the coils... then I'll get hold of an incadescent light bulb and see what happens when the unit is sw...Musaeum — 08:49 PM
Philco 42-345 Restoration/Repair
I have that same set, ain't too much shortwave I like anyway.....it is a good AM DX set. PaulPaul Philco322 — 08:32 PM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum, Martin! Open a new thread in Philco Electronic Restoration when you begin working on your 38-7. ...GarySP — 08:28 PM

[-]
Who's Online
There are currently 1015 online users. [Complete List]
» 1 Member(s) | 1014 Guest(s)
Avatar

>