Philco 89L-troubles

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 89L-troubles

vecher
Phorum Expert

Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA

#31

10-18-2018, 11:09 PM

Ok tried alignment.. Much better.. But noticed the Low end of band is very deaf..from about 600-900 Khz.. It is working since I can inject a signal from SG But levels is very high in order of -20 Dbm..Also noticed that if I put my finger on the RF tube it helps a lot.. Same thing on SW band Signal from Generator can hear but takes a higher signal..

Maybe weak RF tube? The Antenna coil checked out OK.. Not open..

Any clues??

Skip

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Philco 89L-troubles - by vecher - 04-30-2018, 08:41 PM

RE: Philco 89L - by KCMike - 04-30-2018, 09:02 PM

RE: Philco 89L - by Chas - 05-02-2018, 08:27 PM

RE: Philco 89L - by vecher - 06-24-2018, 11:07 AM

RE: Philco 89L - by Radioroslyn - 06-24-2018, 11:49 AM

RE: Philco 89L - by vecher - 06-24-2018, 02:01 PM

RE: Philco 89L - by Radioroslyn - 06-24-2018, 02:57 PM

RE: Philco 89L - by vecher - 06-24-2018, 04:17 PM

RE: Philco 89L - by vecher - 08-03-2018, 11:28 PM

RE: Philco 89L - by Chas - 08-04-2018, 10:44 AM

RE: Philco 89L - by radio63 - 08-14-2018, 08:12 PM

RE: Philco 89L - by Chas - 08-14-2018, 09:39 PM

RE: Philco 89L - by radio63 - 08-15-2018, 03:23 PM

RE: Philco 89L - by jcassity - 08-18-2018, 10:55 AM

RE: Philco 89L - by vecher - 09-09-2018, 12:22 AM

RE: Philco 89L - by Radioroslyn - 09-09-2018, 01:00 AM

RE: Philco 89L - by vecher - 09-09-2018, 04:30 PM

RE: Philco 89L - by Radioroslyn - 09-09-2018, 06:28 PM

RE: Philco 89L - by vecher - 09-09-2018, 11:43 PM

RE: Philco 89L - by morzh - 09-10-2018, 08:37 AM

RE: Philco 89L-Problems - by vecher - 10-17-2018, 05:04 PM

RE: Philco 89L-troubles - by KCMike - 10-17-2018, 05:13 PM

RE: Philco 89L-troubles - by Radioroslyn - 10-17-2018, 05:51 PM

RE: Philco 89L-troubles - by Steve Davis - 10-17-2018, 06:53 PM

RE: Philco 89L-troubles - by vecher - 10-17-2018, 09:09 PM

RE: Philco 89L-troubles - by vecher - 10-17-2018, 10:49 PM

RE: Philco 89L-troubles - by Radioroslyn - 10-17-2018, 11:08 PM

RE: Philco 89L-troubles - by vecher - 10-18-2018, 12:01 PM

RE: Philco 89L-troubles - by vecher - 10-18-2018, 03:16 PM

RE: Philco 89L-troubles - by vecher - 10-18-2018, 08:24 PM

RE: Philco 89L-troubles - by vecher - 10-18-2018, 11:09 PM

RE: Philco 89L-troubles - by Arran - 10-19-2018, 03:12 AM

RE: Philco 89L-troubles - by vecher - 10-19-2018, 01:08 PM

RE: Philco 89L-troubles - by klondike98 - 10-19-2018, 01:13 PM

RE: Philco 89L-troubles - by vecher - 10-19-2018, 02:07 PM

RE: Philco 89L-troubles - by vecher - 10-21-2018, 11:35 PM

RE: Philco 89L-troubles - by vecher - 10-22-2018, 09:17 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70. The trim around the base needs to be replaced. If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me