Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 39-25T
#2

Radio Daze makes the white and black dial reproduction.  Same dial is used on the 39-30 and 39-25.

There is a metal escutcheon that goes over the top of the area for the dial.  The escutcheon holds the station labels in some slots.  New buttons are available from Renovated Radios.

This is what I started with...
[Image: https://www.dropbox.com/s/q98egefokc81ad....jpg?raw=1]

Here's the best close up of the escutcheon I have:
[Image: https://www.dropbox.com/s/zs4gzs6la1aohd....jpg?raw=1]

The escutcheon is not reproduced so you will have to find one on a donor chassis. Perhaps an ad in the wanted section here and keep an eye on the ebay offerings.

The buttons are retained by sliding onto the metal slats seen in this photo with the small rubber piece and circle on the slat.  I never found a replacement for the rubber piece but it works fine without it.  the open end of the slat is to the right and unseen in this photo.  
[Image: https://www.dropbox.com/s/iezjbwnnmsuo8i....jpg?raw=1]

some notes and threads on the restoration can be found in the link in the signature below


Messages In This Thread
Philco 39-25T - by Chris h - 01-01-2019, 11:47 PM
RE: Philco 39-25T - by klondike98 - 01-02-2019, 10:46 AM
RE: Philco 39-25T - by Nathan Slingerland - 01-02-2019, 10:59 AM
RE: Philco 39-25T - by klondike98 - 01-02-2019, 11:59 AM
RE: Philco 39-25T - by Phlogiston - 01-02-2019, 01:59 PM
RE: Philco 39-25T - by Chris h - 01-02-2019, 11:57 PM
RE: Philco 39-25T - by Nathan Slingerland - 01-03-2019, 12:14 AM



Users browsing this thread:
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
So what was wrong with the original speaker? Was the cone damaged? Unless it's totally hopeless I would put it aside as ...Arran — 05:31 PM
My collection presentation
There is an article on my site that introduces the first portable radios in my collection. I have only provided a link t...Vlad95 — 01:17 PM
Electrolytic restuffing/internals
Bridkarl This specific cap you have is the easiset type to restuff. I usually cut it at the upper border of the depr...morzh — 11:35 AM
philco predicta
Hi CGL18, First off, welcome to the Philco Phorum. I have not worked on a TV for a while but here are some givens: ...MrFixr55 — 08:22 AM
Another amp build - here I go again!
Sweet! I actually have a Dynaco Mark 4 that I had been running with 6L6s with no mods. Seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM

[-]
Who's Online
There are currently no members online.

>