Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Heathkit GD-1B
#23

Me too. I wasn't going to allow it to get the best of me. Now to see if it really works..

Skip


Messages In This Thread
Heathkit GD-1B - by vecher - 12-31-2018, 06:37 PM
RE: Heathkit GD-1B - by gregb - 12-31-2018, 06:44 PM
RE: Heathkit GD-1B - by Radioroslyn - 12-31-2018, 06:58 PM
RE: Heathkit GD-1B - by vecher - 12-31-2018, 06:59 PM
RE: Heathkit GD-1B - by vecher - 12-31-2018, 07:02 PM
RE: Heathkit GD-1B - by Steve Davis - 12-31-2018, 07:56 PM
RE: Heathkit GD-1B - by Steve Davis - 12-31-2018, 07:57 PM
RE: Heathkit GD-1B - by Radioroslyn - 12-31-2018, 08:03 PM
RE: Heathkit GD-1B - by vecher - 01-01-2019, 10:09 PM
RE: Heathkit GD-1B - by Chas - 01-01-2019, 11:17 PM
RE: Heathkit GD-1B - by vecher - 01-02-2019, 12:11 AM
RE: Heathkit GD-1B - by Radioroslyn - 01-03-2019, 11:28 AM
RE: Heathkit GD-1B - by vecher - 01-09-2019, 01:46 AM
RE: Heathkit GD-1B - by Surfur - 01-17-2019, 01:46 AM
RE: Heathkit GD-1B - by Radioroslyn - 01-17-2019, 10:52 AM
RE: Heathkit GD-1B - by Surfur - 01-17-2019, 01:24 PM
RE: Heathkit GD-1B - by vecher - 01-19-2019, 12:14 AM
RE: Heathkit GD-1B - by vecher - 01-19-2019, 09:39 PM
RE: Heathkit GD-1B - by Surfur - 01-20-2019, 02:58 AM
RE: Heathkit GD-1B - by vecher - 01-20-2019, 11:10 AM
RE: Heathkit GD-1B - by vecher - 01-20-2019, 04:56 PM
RE: Heathkit GD-1B - by KCMike - 01-20-2019, 05:53 PM
RE: Heathkit GD-1B - by vecher - 01-20-2019, 08:29 PM
RE: Heathkit GD-1B - by vecher - 01-21-2019, 12:04 AM
RE: Heathkit GD-1B - by vecher - 02-15-2019, 09:17 PM
RE: Heathkit GD-1B - by EdHolland - 02-15-2019, 09:39 PM
RE: Heathkit GD-1B - by Surfur - 03-12-2019, 10:12 PM
RE: Heathkit GD-1B - by EdHolland - 03-12-2019, 11:57 PM
RE: Heathkit GD-1B - by vecher - 03-13-2019, 03:00 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently no members online.

>