1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Latest on the 37-650
Bill Hutchinson
Member
***
Posts: 236
Threads: 30
Joined: Sep 2005
City: Minneapolis/St. Paul MN
#2

02-13-2006, 09:02 PM
Scott,

From your description, it sounds like scenario #2 is your most likely problem. You've probably whacked it out of alignment enough to cause a multitude of problems (I'm trying to be kind here, trust me Icon_smile ). Also, #1 is also a likely issue as well. Put your temporary volume control back in for now - it'll do in the short run.

Since it's motorboating, this is a good indication the alignment is way off. Go through the procedure step by step, and keep repeating it until you get some satisfactory results.

Keep at it - you can do this! We're all pulling for you!

Bill
Sent from my Pentium II on the AT&T Dial Network
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Latest on the 37-650 - by Robbie Roberts - 02-13-2006, 06:42 PM
[No subject] - by Bill Hutchinson - 02-13-2006, 09:02 PM
[No subject] - by Robbie Roberts - 02-13-2006, 09:07 PM
[No subject] - by Bill Hutchinson - 02-13-2006, 09:16 PM
[No subject] - by Chuck Schwark - 02-13-2006, 09:52 PM
[No subject] - by Robbie Roberts - 02-14-2006, 12:15 AM
[No subject] - by Robbie Roberts - 02-14-2006, 04:49 AM
[No subject] - by Steve Chambers - 02-14-2006, 08:14 AM
[No subject] - by Robbie Roberts - 02-14-2006, 01:32 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently 954 online users. [Complete List]
» 1 Member(s) | 953 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration