Lowe HF-150

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Lowe HF-150

EdHolland
Super Moderator

Posts: 1,385
Threads: 45
Joined: Nov 2017
City: Menlo Park State, Province, Country: CA

03-04-2019, 03:17 PM

A rather busy weekend limited bench time, but I did get started.

Mounting the keypad to the box required a slot to be cut to pass the pins through from outside. Found I needed to order 2-56 screws to attach the keypad, and the position of the fixing holes is tight with respect to the holes for the screws that hold the box together. It should just work though..

After that, it was back to the drawing board, to start translation of the schematic to a layout on strip board. Takes me back to the projects I used to make as a teenager Icon_smile

. This is about 50% done, and I can work on the remainder over the next few evenings and be ready for building in time for the weekend.

Ed

I don't hold with furniture that talks.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Lowe HF-150 - by EdHolland - 10-19-2018, 04:08 PM

RE: Lowe HF-150 - by EdHolland - 11-23-2018, 10:56 PM

RE: Lowe HF-150 - by Radioroslyn - 11-23-2018, 11:37 PM

RE: Lowe HF-150 - by EdHolland - 11-24-2018, 01:59 AM

RE: Lowe HF-150 - by EdHolland - 03-01-2019, 05:10 PM

RE: Lowe HF-150 - by EdHolland - 03-04-2019, 03:17 PM

RE: Lowe HF-150 - by EdHolland - 03-09-2019, 11:04 PM

RE: Lowe HF-150 - by EdHolland - 03-10-2019, 10:06 PM

RE: Lowe HF-150 - by EdHolland - 03-11-2019, 04:18 PM

RE: Lowe HF-150 - by lapisxmuc1 - 03-15-2021, 12:26 PM

RE: Lowe HF-150 - by Arran - 03-16-2021, 11:35 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me