1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 1 Vote(s) - 2 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 116B chassis restoration
klondike98
Phorum Moderator
******
Posts: 5,170
Threads: 274
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#45

05-13-2019, 02:55 PM
I finally got to work on putting the shadowgraph back together thanks to KCMike.

[Image: https://www.dropbox.com/s/snp6zmzbk869o4....jpg?raw=1]

I also picked up an 18 chassis that had an output transformer on the speaker that would replace the half working one in this set...the fellow at Kutztown said it was working but after getting it home and checking...the field coil is good but the transformer is not... one side of the PushPull should be about 150 ohms but is 2Meg and the other is open...   Icon_redface   That'll teach me to leave my DVM at home.  The entire chassis was only $20 so no big deal.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco 116B chassis restoration - by klondike98 - 11-05-2018, 08:05 PM
RE: Philco 116B chassis restoration - by amptramp - 11-05-2018, 08:41 PM
RE: Philco 116B chassis restoration - by Arran - 11-07-2018, 04:32 AM
RE: Philco 116B chassis restoration - by morzh - 11-15-2018, 03:44 PM
RE: Philco 116B chassis restoration - by KCMike - 11-20-2018, 07:39 PM
RE: Philco 116B chassis restoration - by KCMike - 12-03-2018, 10:03 PM
RE: Philco 116B chassis restoration - by Arran - 12-30-2018, 04:53 PM
RE: Philco 116B chassis restoration - by KCMike - 01-20-2019, 06:09 PM
RE: Philco 116B chassis restoration - by klondike98 - 05-13-2019, 02:55 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 766 online users. [Complete List]
» 1 Member(s) | 765 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration